ENTRY AND START SYSTEM(for Entry Function) Front Passenger Side Door Entry Lock and Unlock Functions do not Operate

DESCRIPTION

If the entry lock and unlock functions do not operate for the front passenger door only, the request code may not be being transmitted from the front passenger door or the front door outside handle assembly (for front passenger door) (touch sensor) may be malfunctioning. If the entry functions for other doors operate properly, communication between the electrical key transmitter sub-assembly and door control receiver is normal. In this case, there may be a problem with request code transmission (communication between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for front passenger door) [front passenger door electrical key antenna]), or there may be wave interference.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

PROCEDURE

1. CHECK POWER DOOR LOCK OPERATION

   
   

   1. When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation Click here.

      OK
      Door locks operate normally.

   
   

   NG

   GO TO POWER DOOR LOCK CONTROL SYSTEM Click here

   OK

2. CHECK WAVE ENVIRONMENT

   
   
   1. 

      Text in Illustration

      *A	for LHD
      *B	for RHD
      *a	Approximately 0.3 m (0.98 ft.)

      Bring the electrical key transmitter sub-assembly approximately 0.3 m (0.98 ft.) from the front door outside handle assembly (for front passenger door) and perform an entry function check Click here.

      Note

      If the electrical key transmitter sub-assembly is brought within 0.2 m (0.66 ft.) of the door handle, communication may not possible.

      Tech Tips

      If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of electric wave interference is high. Also, added vehicle components may cause electric wave interference. If installed, remove them and perform the operation check.

      Result

      Result	Proceed to
      Entry function does not operate normally.	A
      Entry function operates normally.	B

   
   

   B

   AFFECTED BY WAVE INTERFERENCE

   A

3. CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE - CERTIFICATION ECU)

   
   

   1. Disconnect the m1*1 or n1*2 front door outside handle assembly (for front passenger door) connector.

   2. Disconnect the L62 certification ECU (smart key ECU assembly) connector.

   3. Measure the resistance according to the value(s) in the table below.

      
      

      • *1: for LHD

      • *2: for RHD

      Standard Resistance
      for LHD Tester Connection Condition Specified Condition m1-3 (ANT2) - L62-6 (CG2B) Always Below 1 Ω m1-6 (ANT1) - L62-5 (CLG2) Always Below 1 Ω m1-5 (B) - L62-33 (POS2) Always Below 1 Ω m1-2 (GND) - Body ground Always Below 1 Ω m1-3 (ANT2) or L62-6 (CG2B) - Body ground Always 10 kΩ or higher m1-6 (ANT1) or L62-5 (CLG2) - Body ground Always 10 kΩ or higher m1-5 (B) or L62-33 (POS2) - Body ground Always 10 kΩ or higher
      for RHD Tester Connection Condition Specified Condition n1-3 (ANT2) - L62-6 (CG2B) Always Below 1 Ω n1-6 (ANT1) - L62-5 (CLG2) Always Below 1 Ω n1-5 (B) - L62-33 (POS2) Always Below 1 Ω n1-2 (GND) - Body ground Always Below 1 Ω n1-3 (ANT2) or L62-6 (CG2B) - Body ground Always 10 kΩ or higher n1-6 (ANT1) or L62-5 (CLG2) - Body ground Always 10 kΩ or higher n1-5 (B) or L62-33 (POS2) - Body ground Always 10 kΩ or higher

   
   

   NG

   REPAIR OR REPLACE HARNESS OR CONNECTOR

   OK

4. CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO FRONT PASSENGER DOOR ELECTRICAL KEY ANTENNA)

   
   
   1. 

      Text in Illustration

      *A	for LHD
      *B	for RHD
      *1	Waveform
      *a	Front view of wire harness connector (to Front Door Outside Handle Assembly (for front passenger door))

      Disconnect the m1*1 or n1*2 front door outside handle assembly (for front passenger door) connector.

   2. Connect the L62 certification ECU (smart key ECU assembly) connector.

   3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition m1-5 (B) - Body ground*1 n1-5 (B) - Body ground*2 Power switch off → on (IG) 9 to 14 V → Below 2 V

   4. Using an oscilloscope, check the waveform.

      OK
      Tester Connection Condition Tool Setting Specified Condition m1-3 (ANT2) - m1-6 (ANT1)*1 n1-3 (ANT2) - n1-6 (ANT1)*2 Procedure: Power switch off Key brought outside vehicle All doors closed Key not inside vehicle All doors locked through wireless operation 2 V/DIV., 500 ms/DIV. Pulse generation (See waveform)

      
      

      • *1: for LHD

      • *2: for RHD

   
   

   NG

   REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

   OK

5. REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR)

   
   

   1. Temporarily replace the front door outside handle assembly (for front passenger door) with a new or normally functioning one Click here.

   
   

   NEXT

6. CHECK FRONT DOOR OUTSIDE HANDLE ASSEMBLY (OPERATION)

   
   

   1. Check that the entry functions operate normally Click here.

      OK
      Entry functions operate normally.

   
   

   OK

   END (FRONT DOOR OUTSIDE HANDLE ASSEMBLY WAS DEFECTIVE)

   NG

   REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)