SLIDING ROOF SYSTEM DATA LIST / ACTIVE TEST
READ DATA LIST
Tip:Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Note:In the following table, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Sliding Roof or Main Body / Data List.
Read the Data List according to the display on the GTS.
Body Electrical > Sliding Roof > Data List
Tester Display
Measurement Item
Range
Normal Condition
Diagnostic Note
Open Switch
OPEN switch signal
ON or OFF
ON: OPEN switch pressed
OFF: OPEN switch not pressed
-
Close Switch
CLOSE switch signal
ON or OFF
ON: CLOSE switch pressed
OFF: CLOSE switch not pressed
-
Up Switch
UP switch signal
ON or OFF
ON: UP switch pressed
OFF: UP switch not pressed
-
Down Switch
DOWN switch signal
ON or OFF
ON: DOWN switch pressed
OFF: DOWN switch not pressed
-
Rear SW Auto Operation
Sliding roof auto function
ON or OFF
Customization status displayed
This item is not applicable to this vehicle
Front SW Auto Operation
Sliding roof auto function
ON or OFF
Customization status displayed
-
Hall IC1 Pulse
Hall IC1 pulse output
Lo or Hi
Lo and Hi repeat during motor operation
Lo: Hall IC1 output is low
Hi: Hall IC1 output is high
Hall IC1 Status
Status of Hall IC1
Normal or Error
Normal: Hall IC1 normal
Error: Hall IC1 not normal
-
Hall IC2 Pulse
Hall IC2 pulse output
Lo or Hi
Lo and Hi repeat during motor operation
Lo: Hall IC2 output is low
Hi: Hall IC2 output is high
Hall IC2 Status
Status of Hall IC2
Normal or Error
Normal: Hall IC2 normal
Error: Hall IC2 not normal
-
Ignition (Direct Signal)
Ignition switch signal
ON or OFF
ON: Ignition switch ON
OFF: Ignition switch off
-
Ignition (MPX)
Ignition switch signal (LIN signal)
ON or OFF
ON: Ignition switch ON
OFF: Ignition switch off
-
Door Courtesy
Driver door courtesy light switch signal
ON or OFF
ON: Driver door open
OFF: Driver door closed
-
Door Handle Lock Button
Entry lock switch
ON or OFF
ON: Entry lock switch is pressed
OFF: Entry lock switch is not pressed
This item is not applicable to this vehicle
Door Key Close Operation
Key-linked sliding roof close signal
ON or OFF
ON: Door LOCK is turned to close position using key
OFF: Door LOCK is not turned
This item is not applicable to this vehicle
Door Key Open Operation
Key-linked sliding roof open signal
ON or OFF
ON: Door UNLOCK is turned to open position using key
OFF: Door UNLOCK is not turned
This item is not applicable to this vehicle
Wireless Close Operation
Wireless sliding roof close signal
ON or OFF
ON: Transmitter LOCK switch pressed
OFF: Transmitter LOCK switch not pressed
This item is not applicable to this vehicle
Wireless Open Operation
Wireless sliding roof open signal
ON or OFF
ON: Transmitter UNLOCK switch pressed
OFF: Transmitter UNLOCK switch not pressed
This item is not applicable to this vehicle
Key Off Permission
Key-off sliding roof operation permit signal
ON or OFF
ON: Front doors are not opened within 43 seconds after ignition switch turned off
OFF: Any status except "ON" status
-
Window Lock
Window lock operation signal
ON or OFF
ON: Window lock switch is turned to lock
OFF: Window lock switch is turned to unlock
This item is not applicable to this vehicle
Door Key Related Operation
Key-linked sliding roof open function operating direction
Slide or Tilt
Customization status displayed
This item is not applicable to this vehicle
Wireless Key Rel Operation
Wireless transmitter-linked sliding roof open function operating direction
Slide or Tilt
Customization status displayed
This item is not applicable to this vehicle
Open Switch Failure(Past)
Open switch failure signal (Past)
ON or OFF
ON: Sliding roof open switch failure signal (Past)
OFF: No sliding roof open switch failure signal (Past)
-
Close Switch Failure(Past)
Close switch failure signal (Past)
ON or OFF
ON: Sliding roof close switch failure signal (Past)
OFF: No sliding roof close switch failure signal (Past)
-
Up Switch Failure(Past)
Up switch failure signal (Past)
ON or OFF
ON: Sliding roof tilt up switch failure signal (Past)
OFF: No sliding roof tilt up switch failure signal (Past)
-
Down Switch Failure(Past)
Down switch failure signal (Past)
ON or OFF
ON: Sliding roof tilt down switch failure signal (Past)
OFF: No sliding roof tilt down switch failure signal (Past)
-
Open Switch Failure(Current)
Open switch failure signal (Current)
ON or OFF
ON: Sliding roof open switch failure signal (Current)
OFF: No sliding roof open switch failure signal (Current)
-
Close Switch Failure(Current)
Close switch failure signal (Current)
ON or OFF
ON: Sliding roof close switch failure signal (Current)
OFF: No sliding roof close switch failure signal (Current)
-
Up Switch Failure(Current)
Up switch failure signal (Current)
ON or OFF
ON: Sliding roof tilt up switch failure signal (Current)
OFF: No sliding roof tilt up switch failure signal (Current)
-
Down Switch Failure(Current)
Down switch failure signal (Current)
ON or OFF
ON: Sliding roof tilt down switch failure signal (Current)
OFF: No sliding roof tilt down switch failure signal (Current)
-
Number of Trouble Codes
Number of DTCs
Min.: 0, Max.: 255
Number of stored DTCs
-
Body Electrical > Main Body > Data List
Tester Display
Measurement Item
Range
Normal Condition
Diagnostic Note
Slide Roof Open Warning
Sliding roof open warning
ON or OFF
Customization status displayed
-
PERFORM ACTIVE TEST
Tip:Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Sliding Roof / Active Test.
Perform the Active Test according to the display on the GTS.
Body Electrical > Sliding Roof > Active Test
Tester Display
Measurement Item
Control Range
Diagnostic Note
Slide Roof
Operate sliding roof motor
OFF / Opn/Dwn / Clos/Up
-