ROOF HEADLINING(for Sedan) REASSEMBLY

PROCEDURE

1. INSTALL NO. 1 HEADLINING LIGHT CASE

   1. 

      *a	Marking
      *b	Front

      Align the new No. 1 headlining light case with the marking on the roof headlining assembly and install it using hot-melt glue as shown in the illustration.

2. INSTALL NO. 2 HEADLINING LIGHT CASE (w/ Vanity Light)

   1. 

      *a	Marking
      *b	Front

      Align the 2 new No. 2 headlining light cases with the markings on the roof headlining assembly and install them using hot-melt glue as shown in the illustration.

3. INSTALL NO. 1 ROOF WIRE

   1. Pass the No. 1 roof wire through the front tab of the roof headlining assembly.

      

      *A	for LHD without Pre-crash Safety System	*B	for LHD with Pre-crash Safety System
      *C	for RHD without Pre-crash Safety System	*D	for RHD with Pre-crash Safety System
      *E	w/ EC Mirror	*F	w/ Rain Sensor
      *G	w/ Vanity Light	-	-
      *a	Marking	*b	Front Tab
      	Positioning Tape (A)		Positioning Tape (B)
      	Adhesive Tape	-	-

   2. Align the positioning tape (A) on the front part of the No. 1 roof wire with the front tab of the roof headlining assembly.

   3. Align the positioning tape (B) on the No. 1 roof wire with the markings on the roof headlining assembly.

   4. Install the No. 1 roof wire to the roof headlining assembly with adhesive tape.

      Note:

      • Apply the tape securely in place.

      • Do not touch the adhesive surface when applying the tape to prevent adhesion failure.

4. INSTALL NO. 2 ROOF SILENCER PAD

   1. Align the 2 new No. 2 roof silencer pads with the markings on the roof headlining assembly and install them using hot-melt glue as shown in the illustration.

      

      *a

      Marking

      -

      -

5. INSTALL NO. 1 ROOF SILENCER PAD (except Cold Area)

   1. Align the 2 new No. 1 roof silencer pads with the markings on the roof headlining assembly and install them using hot-melt glue as shown in the illustration.

      

      *a

      Marking

      -

      -

6. INSTALL NO. 1 ROOF SILENCER PAD (for Cold Area)

   1. Align the new No. 1 roof silencer pad with the markings on the roof headlining assembly and install it using hot-melt glue as shown in the illustration.

      

      *a

      Marking

      -

      -

7. INSTALL FRONT ROOF SILENCER PAD (except Cold Area)

   1. 

      *a

      Marking

      Align the new front roof silencer pad with the markings on the roof headlining assembly and install it using hot-melt glue as shown in the illustration.

8. INSTALL ROOF SILENCER PAD (for Cold Area)

   1. Remove the release paper from 2 new roof silencer pads.

      Tip:

      After removing the release paper, keep the exposed adhesive free from foreign matter.

   2. 

      *a

      Marking

      Align the 2 roof silencer pads with the markings on the roof headlining assembly and install them as shown in the illustration.

9. INSTALL NO. 4 ROOF SILENCER PAD (for Cold Area)

   1. Remove the release paper from a new No. 4 roof silencer pad.

      Tip:

      After removing the release paper, keep the exposed adhesive free from foreign matter.

   2. 

      *a

      Marking

      Align the No. 4 roof silencer pad with the markings on the roof headlining assembly and install it as shown in the illustration.

10. INSTALL NO. 1 AMPLIFIER ANTENNA ASSEMBLY

    Click here

11. INSTALL VANITY LIGHT ASSEMBLY (w/ Vanity Light)

    Click hereClick here