SFI SYSTEM(w/ Canister Pump Module), Diagnostic DTC:P219962

DTC Code DTC Name
P219962 Intake Air Temperature Sensor 1/2 Correlation Signal Compare Failure

DESCRIPTION

Refer to DTC P00AA11.

Click here

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P219962 Intake Air Temperature Sensor 1/2 Correlation Signal Compare Failure The difference between the temperature of the intake air temperature (mass air flow meter sub-assembly) bank 1 and bank 2 is Higher than 20°C (68°F) (2 trip detection logic).

  • Mass air flow meter sub-assembly (bank 1)

  • Mass air flow meter sub-assembly (bank 2)

 Comes on DTC stored SAE: P2199

MONITOR DESCRIPTION

This DTC is stored when a deviation from intake air temperature sensor characteristics is detected. The intake air temperature sensors are checked 420 minutes after the engine switch is turned off. If the pressures detected by the intake air temperature sensors differ by a certain amount, the MIL is illuminated and a DTC is stored (2 trip detection logic).

MONITOR STRATEGY

Required Sensors/Components Intake air temperature sensor (mass air flow meter sub-assembly)
Frequency of Operation Once per driving cycle

CONFIRMATION DRIVING PATTERN

B006CXUE54

  1. Connect the GTS to the DLC3.

  2. Turn the engine switch on (IG).

  3. Turn the GTS on.

  4. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure) [A].

  5. Turn the engine switch off.

  6. With the engine stopped, leave the vehicle as is for 7.5 hours or more [B].

  7. Turn the engine switch on (IG).

  8. Turn the GTS on.

  9. Start the engine and wait 120 seconds or more [C].

  10. Enter the following menus: Powertrain / Engine / Trouble Codes [D].

  11. Read the pending DTCs.

    Tech Tips


    • If a pending DTC is output, the system is malfunctioning.

    • If a pending DTC is not output, perform the following procedure.

  12. Enter the following menus: Powertrain / Engine / Utility / All Readiness.

  13. Input the DTC: P219962.

  14. Check the DTC judgment result.

    GTS Display Description
    NORMAL

    • DTC judgment completed

    • System normal
    ABNORMAL

    • DTC judgment completed

    • System abnormal
    INCOMPLETE

    • DTC judgment not completed

    • Perform driving pattern after confirming DTC enabling conditions

    Tech Tips


    • If the judgment result is NORMAL, the system is normal.

    • If the judgment result is ABNORMAL, the system is malfunctioning.

    • If the judgment result is INCOMPLETE, perform steps [B] through [D] again.

CAUTION / NOTICE / HINT

Tech Tips

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE


  1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO P219962)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine / Trouble Codes.

    5. Read the DTCs.


      Powertrain > Engine > Trouble Codes
      Result
      Result Proceed to
      DTC P219962 is output A
      DTC P219962 and other DTCs are output B

      Tech Tips

      If any DTCs other than P219962 are output, troubleshoot those DTCs first.

    6. Record the freeze frame data.


    B

    GO TO DTC CHART Click here

    A

  2. CHECK FREEZE FRAME DATA (COOLANT TEMPERATURE SENSOR3, INTAKE AIR TEMPERATURE B1S1 AND INTAKE AIR TEMPERATURE B2S1)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Using the GTS, read the values displayed in the freeze frame data recorded in step 1.


      Powertrain > Engine > DTC(P219962) > Freeze Frame Data
      Tester Display
      Coolant Temperature Sensor3
      Intake Air Temperature B1S1
      Intake Air Temperature B2S1

    5. Compare the difference in temperatures between "Intake Air Temperature B1S1 and Coolant Temperature Sensor3" and "Intake Air Temperature B2S1 and Coolant Temperature Sensor3".

      Tech Tips


      • When the engine is cold, the value of the engine coolant temperature and intake air temperature should be approximately the same.

      • If the result is not as specified, check that there are no heat sources such as a block heater in the engine compartment.

      • Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.

        Click here

      Result
      Result Proceed to
      There is a large difference in temperature between Intake Air Temperature B1S1 and Coolant Temperature Sensor3 A
      There is a large difference in temperature between Intake Air Temperature B2S1 and Coolant Temperature Sensor3 B

    A

    REPLACE MASS AIR FLOW METER SUB-ASSEMBLY (BANK 1) Click here

    B

    REPLACE MASS AIR FLOW METER SUB-ASSEMBLY (BANK 2) Click here