CANISTER(w/ Canister Pump Module) REMOVAL

PROCEDURE


  1. REMOVE NO. 1 FLOOR UNDER COVER


    1. B0069Y3C02
      B006AHR Clip A
      B006EC9 Clip B
      B006FCW Grommet

      Detach the 6 clips and remove the 5 grommets and No. 1 floor under cover.

  2. DISCONNECT FUEL TANK VENT HOSE SUB-ASSEMBLY


    1. Disconnect the fuel tank vent hose sub-assembly from the charcoal canister assembly.


      1. B006EPOC01
        *a Tab
        *b Retainer
        B006AHR Pinch
        B006EC9 Pull

        Pinch the tabs of the retainer to detach the lock claws and pull it down.

        Note


        • Remove any dirt or foreign matter on the tube connector before performing this work.

        • Do not allow any scratches or foreign matter to get on the parts when disconnecting them as the tube connector has an O-ring that seals the pipe (charcoal canister assembly).

        • Perform this work by hand. Do not use any tools.

        • Do not forcibly bend, twist or turn the fuel tank vent hose sub-assembly.

        • Protect the disconnected parts by covering them with plastic bags after disconnecting the fuel tank vent hose sub-assembly.

        • If the tube connector and pipe (charcoal canister assembly) are stuck, push and pull to release them.

        B006CGHC01
        *a Tube Connector
        *b Pipe (Charcoal Canister Assembly)
        *c O-Ring
        *d Retainer

        Tech Tips

        Do not remove the retainer.

      2. Pull off the fuel tank vent hose sub-assembly from the pipe (charcoal canister assembly).

  3. DISCONNECT CHARCOAL CANISTER OUTLET TUBE SUB-ASSEMBLY


    1. Disconnect the charcoal canister outlet tube sub-assembly from the fuel outlet valve assembly.


      1. B006C9HC01
        *a Tab
        *b Retainer
        B006AHR Pinch
        B006EC9 Pull

        Pinch the tabs of the retainer to detach the lock claws and pull it down.

        Note


        • Remove any dirt or foreign matter on the tube connector before performing this work.

        • Do not allow any scratches or foreign matter to get on the parts when disconnecting them as the tube connector has an O-ring that seals the pipe (fuel outlet valve assembly).

        • Perform this work by hand. Do not use any tools.

        • Do not forcibly bend, twist or turn the charcoal canister outlet tube sub-assembly.

        • Protect the disconnected parts by covering them with plastic bags after disconnecting the charcoal canister outlet tube sub-assembly.

        • If the tube connector and pipe (fuel outlet valve assembly) are stuck, push and pull to release them.

        B006EI6C01
        *a Tube Connector
        *b Pipe (Fuel Outlet Valve Assembly)
        *c O-Ring
        *d Retainer

        Tech Tips

        Do not remove the retainer.

      2. Pull off the charcoal canister outlet tube sub-assembly from the pipe (fuel outlet valve assembly).

  4. REMOVE CHARCOAL CANISTER ASSEMBLY


    1. B006GR2

      Disconnect the connector from the canister pump module.

    2. B006DTB

      Slide the clamp and disconnect the purge line hose from the fuel tube.

    3. Disconnect the fuel outlet valve assembly from the charcoal canister assembly.


      1. B006AO5C01
        *a Tab
        *b Retainer
        B006AHR Pinch
        B006EC9 Pull

        Pinch the tabs of the retainer to detach the lock claws and pull it down.

        Note


        • Remove any dirt or foreign matter on the tube connector before performing this work.

        • Do not allow any scratches or foreign matter to get on the parts when disconnecting them as the tube connector has an O-ring that seals the pipe (charcoal canister assembly).

        • Perform this work by hand. Do not use any tools.

        • Do not forcibly bend, twist or turn the fuel outlet valve assembly.

        • Protect the disconnected parts by covering them with plastic bags after disconnecting the fuel tank vent hose sub-assembly.

        • If the tube connector and pipe (charcoal canister assembly) are stuck, push and pull to release them.

        B006DR1C01
        *a Tube Connector
        *b Pipe (Charcoal Canister Assembly)
        *c O-Ring
        *d Retainer

        Tech Tips

        Do not remove the retainer.

      2. Pull off the fuel outlet valve assembly from the pipe (charcoal canister assembly).

    4. B006BXTC01
      *1 Purge Line Hose

      Detach the clip and disconnect the purge line hose.

    5. Remove the 4 nuts, clip and charcoal canister assembly from the body.

  5. REMOVE FUEL OUTLET VALVE ASSEMBLY


    1. B006G7F

      Remove the 2 nuts and fuel outlet valve assembly from the body.

  6. REMOVE CANISTER PUMP MODULE

    Tech Tips

    Only perform this procedure when replacement of the canister pump module is necessary.


    1. Before removing the canister pump module, clean the charcoal canister assembly by blowing air into it to ensure that the charcoal canister assembly is free of foreign matter.

      Note


      • Make sure to clean the charcoal canister assembly using air only.

      • Do not use gasoline, thinners or solvents.

    2. B006CBY

      Detach the 2 claws and remove the canister pump module from the filter assembly.

      Tech Tips

      Tape the screwdriver tip before use.

    3. Check if the filter assembly contains foreign matter such as mud or water.


      1. B006AIF

        Visually check that the inside of the filter assembly is free of foreign matter.

      2. Hold the filter assembly upside down to make sure that it is free of foreign matter.

        If the filter assembly contains foreign matter, replace the canister pump module.