ROOF HEADLINING (w/ Roof Window Glass) REMOVAL

PRECAUTION

Note

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (- ) battery terminal notices before proceeding with work Click here.
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Note

When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.
REMOVE NO. 2 ROOM LIGHT ASSEMBLY
Tech Tips

Use the same procedure described for the other side.
1. Text in Illustration
  
  *1 Protective Tape
  
  Using a screwdriver, detach the 4 claws and remove the light cover.
  
  Tech Tips
  
  Tape the screwdriver tip before use.
2. Remove the 2 screws and No. 2 room light assembly.
3. Disconnect the connector.
REMOVE BACK DOOR SCUFF PLATE (w/ Rear Air Conditioning System)
1. Detach the 7 clips and 4 claws and remove the back door scuff plate.
REMOVE BACK DOOR WEATHERSTRIP (w/ Rear Air Conditioning System)
DISCONNECT REAR NO. 4 SEAT BELT ASSEMBLY OUTER (w/ Rear Air Conditioning System)
Tech Tips

Use the same procedure described for the other side.
1. Using a screwdriver, detach the 4 claws and open the shoulder side cover of the rear No. 4 seat belt assembly outer.
  
  Tech Tips
  
  Tape the screwdriver tip before use.
2. Loosen the bolt and disconnect the shoulder side of the rear No. 4 seat belt assembly outer.
REMOVE ROOF HEADLINING MOULDING (w/o Rear Air Conditioning System)
1. Detach the 18 clips and 2 roof headlining mouldings.
  
  Tech Tips
  
  If any clip remains on the body side, use a clip remover.
REMOVE REAR ROOF HEADLINING GARNISH (w/o Rear Air Conditioning System)
1. Detach the 18 clips and remove the rear roof headlining garnish.
REMOVE REAR ROOF HEADLINING GARNISH (w/ Rear Air Conditioning System)
1. Detach the 18 clips and remove the rear roof headlining garnish.
REMOVE ROOF CLIP (w/o Rear Air Conditioning System)
1. Using a screwdriver, detach the 2 claws and remove the roof clip.
  
  Tech Tips
  
  Tape the screwdriver tip before use.
REMOVE NO. 4 ROOF HEADLINING (w/o Rear Air Conditioning System)
1. Remove the 17 clips and No. 4 roof headlining.
REMOVE NO. 3 ROOF HEADLINING (w/o Rear Air Conditioning System)
1. Remove the 3 clips and No. 3 roof headlining.
REMOVE NO. 2 ROOF HEADLINING (w/o Rear Air Conditioning System)
1. Remove the 5 clips and No. 2 roof headlining.
REMOVE NO. 2 ROOF HEADLINING (w/ Rear Air Conditioning System)
1. Using a clip remover, remove the 18 clips.
2. Using a clip remover, detach the 4 clips A and remove the No. 2 roof headlining.
REMOVE FRONT DOOR SCUFF PLATE LH
1. Detach the 5 clips and remove the front door scuff plate LH.
REMOVE FRONT DOOR SCUFF PLATE RH
1. Detach the 5 clips and remove the front door scuff plate RH.
REMOVE FRONT DOOR OPENING TRIM RH
REMOVE FRONT DOOR OPENING TRIM LH
REMOVE ASSIST GRIP PLUG
1. Using a screwdriver, detach the 4 claws and remove the 2 assist grip plugs.
  Tech Tips
  
  Tape the screwdriver tip before use.
  
  Use the same procedure described for the other side.
REMOVE ASSIST GRIP ASSEMBLY
1. Remove the 2 screws and assist grip assembly.
  
  Tech Tips
  
  Use the same procedure described for the other side.
REMOVE FRONT PILLAR GARNISH RH
1. Detach the clip and 2 claws and remove the front pillar garnish RH.
REMOVE FRONT PILLAR GARNISH LH

Tech Tips

Use the same procedure described for the RH side.
DISCONNECT REAR NO. 3 SEAT BELT ASSEMBLY OUTER (w/ Rear Air Conditioning System)
1. Using a screwdriver, detach the 4 claws and open the shoulder side cover of the rear No. 3 seat belt assembly outer.
  
  Tech Tips
  
  Tape the screwdriver tip before use.
2. Loosen the bolt and disconnect the shoulder side of the rear No. 3 seat belt assembly outer.
REMOVE ASSIST GRIP (w/o Rear Air Conditioning System)
1. Text in Illustration
  
  *1 Protective Tape
  
  Using a screwdriver, detach the 6 claws and open the 2 assist grip covers.
  
  Tech Tips
  
  Tape the screwdriver tip before use.
2. Remove the 2 screws and assist grip.
REMOVE CENTER PILLAR GARNISH COVER LOWER LH (w/ Rear Air Conditioning System)
1. Using a screwdriver, detach the 4 claws and remove the center pillar garnish cover lower LH.
  
  Tech Tips
  
  Tape the screwdriver tip before use.
REMOVE SEAT ASSEMBLY LH (w/ Rear Air Conditioning System)
1. Disconnect connector.
2. Remove the nut and 3 bolts.
3. Remove the seat assembly LH.
REMOVE SEAT BELT ANCHOR COVER (w/ Rear Air Conditioning System)
1. Remove the 2 clips.
2. Detach the claw and then remove the seat belt anchor cover.
DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH (w/ Rear Air Conditioning System)
1. Remove the bolt and disconnect the front seat outer belt assembly LH.
2. Text in Illustration
  
  *1 Protective Tape
  
  Using a screwdriver, detach the 2 claws and open the cover.
  
  Tech Tips
  
  Tape the screwdriver tip before use.
3. Remove the bolt and disconnect the front seat outer belt assembly LH.
REMOVE CENTER PILLAR GARNISH LOWER LH (w/ Rear Air Conditioning System)
1. Using a screwdriver, detach the 4 clips and remove the center pillar garnish lower LH.
REMOVE ENGINE SERVICE HOLE COVER HOOK NO. 2 LH (w/ Rear Air Conditioning System)
1. Remove the screw and the engine service hole cover hook No. 2 LH.
REMOVE CENTER PILLAR GARNISH LH (w/ Rear Air Conditioning System)
1. Using a screwdriver, detach the 3 clips and claw, and remove the center pillar garnish LH.
REMOVE REAR DOOR SCUFF PLATE RH (w/ Rear Air Conditioning System)
1. Detach the 11 clips and remove the rear door scuff plate RH.
REMOVE SLIDE DOOR WEATHERSTRIP NO. 1 RH (w/ Rear Air Conditioning System)
DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH (w/ Rear Air Conditioning System)
1. Remove the bolt and disconnect front seat outer belt assembly RH.
2. Text in Illustration
  
  *1 Protective Tape
  
  Using a screwdriver, detach the 2 claws and open the cover.
  
  Tech Tips
  
  Tape the screwdriver tip before use.
3. Remove the bolt and disconnect front seat outer belt assembly RH.
REMOVE CENTER PILLAR GARNISH LOWER RH (w/ Rear Air Conditioning System)
1. Remove the clip.
2. Using a screwdriver, detach the 4 clips and remove the center pillar garnish lower RH.
  
  Tech Tips
  
  Tape the screwdriver tip before use.
REMOVE CENTER PILLAR GARNISH RH (w/ Rear Air Conditioning System)
1. Detach the 3 clips, claw and remove the center pillar garnish RH.
REMOVE BACK WINDOW GLASS HAMMER ASSEMBLY (w/ Rear Air Conditioning System)
Tech Tips

Use the same procedure for all back window glass hammers.
1. Remove the 2 bolts.
2. Detach the claw and 2 guides.
3. Disconnect the connector and remove the back window glass hammer.
  
  Text in Illustration
  
  *A for Super Long Wheelbase *B for Long Wheelbase
REMOVE NO. 1 ROOM LIGHT ASSEMBLY
1. Text in Illustration
  
  *1 Protective Tape
  
  Using a screwdriver, detach the 4 claws and remove the light cover.
  
  Tech Tips
  
  Tape the screwdriver tip before use.
2. Remove the 2 screws and No. 1 room light assembly.
3. Disconnect the connector.
REMOVE VISOR ASSEMBLY LH
1. Remove the 2 screws and visor assembly LH.
REMOVE VISOR ASSEMBLY RH

Tech Tips

Use the same procedures described for the LH side.
REMOVE VISOR HOLDER
Tech Tips

Use the same procedure described for the other side.
1. Remove the screw.
2. Using a moulding remover, detach the claw and remove the visor holder.
REMOVE REAR COOLER CONTROL PANEL (w/ Rear Air Conditioning System)
1. Release the 4 clips and 4 claws, and disconnect the rear cooler control panel.
2. Disconnect the connector and remove the rear cooler control panel.
REMOVE NO. 1 ROOF HEADLINING (w/o Rear Air Conditioning System)
1. Using a clip remover, remove the 6 clips.
2. Using a clip remover, detach the clip A and remove the No. 1 roof headlining.
REMOVE NO. 1 ROOF HEADLINING (w/ Rear Air Conditioning System)
1. Remove the 4 screws.
2. Using a clip remover, remove the 10 clips.
3. Using a clip remover, detach the clip A and remove the roof headlining No. 1.