REAR BRAKE FLEXIBLE HOSE INSTALLATION

CAUTION / NOTICE / HINT

Note


  • Because the left and right rear flexible hoses are not interchangeable, verify the part number when installing the flexible hoses.

  • If the hoses are to be reused, connect them after checking the identification marks placed when each hose was disconnected.

Tech Tips


  • Use the same procedure for the LH side and RH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. INSTALL REAR BRAKE TUBE FLEXIBLE HOSE (for LH Side)


    1. Install the rear brake tube flexible hose with the bolt and a new clip.

      A005C84E03
      Text in Illustration
      *a Identification Mark - -
      A005CQU Inside of the Vehicle - -
      Torque:
      19 N*m  { 194 kgf*cm, 14 ft.*lbf }

      Note


      • Install the clip as far as it will go.

      • When installing the rear brake tube flexible hose, face the identification mark to the inside of the vehicle and minimize twisting of the hose.

    2. A005C26

      Using a union nut wrench, connect the 2 brake lines to the rear brake tube flexible hose.

      Torque:
      15 N*m  { 155 kgf*cm, 11 ft.*lbf }

      Note


      • Do not bend or damage the brake line.

      • Do not allow any foreign matter such as dirt and dust to enter the brake line from the connecting points.

      • Use the formula to calculate special torque values for situations where the union nut wrench is combined with a torque wrench Click here.

  2. INSTALL REAR BRAKE TUBE FLEXIBLE HOSE (for RH Side)


    1. Install the rear brake tube flexible hose with 2 new clips.

      A005EGYE03
      Text in Illustration
      *a Identification Mark - -
      A005CQU Inside of the Vehicle - -

      Note


      • Install the clip as far as it will go.

      • When installing the rear brake tube flexible hose, face the identification mark to the inside of the vehicle and minimize twisting of the hose.

    2. A005AJU

      Using a union nut wrench, connect the 2 brake lines to the rear brake tube flexible hose.

      Torque:
      15 N*m  { 155 kgf*cm, 11 ft.*lbf }

      Note


      • Do not bend or damage the brake line.

      • Do not allow any foreign matter such as dirt and dust to enter the brake line from the connecting points.

      • Use the formula to calculate special torque values for situations where the union nut wrench is combined with a torque wrench Click here.

  3. INSTALL REAR FLEXIBLE HOSE


    1. A005EFT

      Connect the rear flexible hose to the rear disc brake cylinder assembly with a new union bolt and a new gasket.

      Torque:
      33 N*m  { 340 kgf*cm, 25 ft.*lbf }
    2. A005CMD

      Install a new clip.

      Note

      Install the clip as far as it will go.

    3. A005AF5

      Using a union nut wrench, connect the brake line to the rear flexible hose while holding the rear flexible hose with a wrench.

      Torque:
      15 N*m  { 155 kgf*cm, 11 ft.*lbf }

      Note


      • Do not bend or damage the brake line.

      • Do not allow any foreign matter such as dirt and dust to enter the brake line from the connecting points.

      • Use the formula to calculate special torque values for situations where the union nut wrench is combined with a torque wrench Click here.

  4. FILL RESERVOIR WITH BRAKE FLUID

  5. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

    Click here

  6. BLEED BRAKE LINE

    Click here

  7. INSTALL REAR WHEEL

    Torque:
    103 N*m  { 1050 kgf*cm, 76 ft.*lbf }