OIL AND OIL FILTER REPLACEMENT

CAUTION / NOTICE / HINT

CAUTION:

  • Prolonged and repeated contact with engine oil will result in the removal of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.

  • Wear protective clothing and gloves. Avoid contact with used oil. If contact occurs, wash your skin thoroughly with soap or waterless hand cleaner. Never use gasoline, thinners, or solvents to wash the skin.

  • In order to protect the environment, dispose of used oil and used oil filters at designated disposal sites only.

PROCEDURE

  1. DRAIN ENGINE OIL

    1. Remove the oil filler cap.

    2. Remove the oil pan drain plug and gasket, and drain the engine oil into a container.

    3. Clean and install a new gasket to the oil pan drain plug.

    4. Install the oil pan drain plug.

      30 N*m

      306 kgf*cm

      22 ft.*lbf

  2. REMOVE OIL FILTER ELEMENT

    1. A202642C09

      *1

      Pipe

      *2

      Hose

      Connect a hose with an inside diameter of 15 mm (0.591 in.) to the pipe.

    2. A197967

      Remove the oil filter drain plug.

    3. A197965C01

      *1

      Oil Filter Cap

      *2

      Valve

      *3

      Pipe

      *4

      O-Ring

      *5

      Hose

      Insert the pipe with the hose into the oil filter cap.

      Note:

      Be sure to insert the pipe with the O-ring installed on the oil filter cap.

      Tip:

      Place the hose end into a container before draining the engine oil.

    4. A197966

      Make sure that the engine oil has been completely drained, and remove the pipe with the hose and O-ring.

      Tip:

      Be sure to turn the pipe in the direction of the arrow to remove it.

    5. A201146E01

      Using SST, remove the oil filter cap.

      09228-06501

    6. A298729C01

      *1

      Oil Filter Element

      *2

      O-ring

      Remove the oil filter element and O-ring from the oil filter cap.

      Note:

      Do not use any tools to remove the O-ring to prevent damage to the oil filter cap assembly.

      Be sure to remove it by hand.

  3. INSTALL OIL FILTER ELEMENT

    1. Clean the inside of the oil filter cap, the threads and O-ring groove.

    2. A268595C05

      *1

      O-ring

      *a

      Correct

      *b

      Incorrect

      Apply a small amount of engine oil to a new O-ring and install it to the oil filter cap.

      Note:

      • Be sure to install the O-ring in the proper location, otherwise engine oil may leak.

      • Do not twist the O-ring.

    3. Set a new oil filter element to the oil filter cap.

    4. Remove any dirt or foreign matter from the installation surface of the engine.

    5. Apply a small amount of engine oil to the O-ring again and temporarily tighten the oil filter cap.

    6. A296403C02

      *1

      Oil Filter Cap

      *2

      O-ring

      *a

      Oil Filter Bracket

      *b

      No Gap

      Using SST, tighten the oil filter cap.

      09228-06501

      40 N*m

      408 kgf*cm

      30 ft.*lbf

      Note:

      • After tightening the oil filter cap, make sure that there is no gap and that the O-ring is not protruding.

      • Do not cross thread the oil filter cap.

    7. A200674C08

      *1

      Oil Filter Drain Plug

      *2

      O-ring

      Apply a small amount of engine oil to a new drain plug O-ring, and install it to the oil filter cap.

      Note:

      Before installing the O-ring, remove any dirt or foreign matter from the installation surface of the oil filter cap.

    8. Install the oil filter drain plug.

      13 N*m

      133 kgf*cm

      10 ft.*lbf

      Note:

      Be careful that the O-ring does not get caught between the parts.

  4. ADD ENGINE OIL

    1. Add new engine oil.

      Table 1. Standard Oil Grade

      Oil Grade

      Oil Viscosity (SAE)

      API grade SL "Energy-Conserving", SM "Energy-Conserving", SN "Resource-Conserving" or ILSAC multigrade engine oil

      • 0W-20

      • 5W-20

      • 5W-30

      • 10W-30

      API grade SL, SM or SN multigrade engine oil

      • 15W-40

      • 20W-50
      Table 2. Standard Capacity

      Item

      Standard Condition

      Drain and refill with oil filter change

      3.4 liters (3.6 US qts, 3.0 Imp. qts)

      Drain and refill without oil filter change

      3.2 liters (3.4 US qts, 2.8 Imp. qts)

      Dry fill

      3.9 liters (4.1 US qts, 3.4 Imp. qts)

    2. Install the oil filler cap.

  5. INSPECT FOR ENGINE OIL LEAK

    1. Warm up the engine. Make sure that there are no engine oil leaks from the area that was worked on.