FRONT SEAT CUSHION HEATER INSTALLATION

CAUTION / NOTICE / HINT

CAUTION:


  • B0025TC

    Wear protective gloves. Sharp areas on the parts may injure your hands.

  • There is risk of injury.

  • If the front seat side airbag was deployed, replace the front seat airbag assembly, separate type front seatback frame sub-assembly, separate type front seatback cover and separate type front seatback pad with the necessary parts in accordance with the extent of the collision damage.

  • Replace any other damaged parts as necessary.

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

PROCEDURE


  1. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER


    1. A01SJ73N01

      Install the seat cover wire.

      Tech Tips


      • There are service parts available for wires of 1000 mm or longer and formed wires.


      • Refer to the precautions when creating a wire.

      Length
      A 170 mm (6.70 in.)
      B 150 mm (5.91 in.)
      C 230 mm (9.06 in.)
      D 270 mm (10.63 in.)
      E 290 mm (11.42 in.)

      Tech Tips


      • A01SGX6

        The dimensions shown in the illustration are the length.


      • Refer to the precautions on wrinkles to avoid creating any on the separate type front seat cushion cover when installing the seat cover.


      • As shown in the illustration, fix all of the cover seam allowances in the same direction.

        A01SIJKN10

    2. Temporarily install the separate type front seat cushion cover to the separate type front seat cushion pad.

    3. Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 18 new hog rings in the order shown in the illustration.

      A01SG2VC01
      *1 Hog Ring Pliers - -
      *a Cutout - -

    4. Using hog ring pliers, connect the 2 straps of the separate type front seat cushion cover to the separate type front seat cushion pad with 2 new hog rings.

      Tech Tips


      • Do not dirty or damage the separate type front seatback cover.


      • Securely tighten the hog rings as shown in the illustration while making sure wrinkles do not form in the center of the fabric and separate type front seatback pad.

      A01SHL8C01
      *1 Hog Ring Pliers - -

  2. INSTALL SEAT CUSHION COVER WITH PAD

    for Manual Seat:

    Click here

    for Power Seat:

    Click here

  3. INSTALL FRONT SEATBACK FRAME SUB-ASSEMBLY LH

    for Manual Seat:

    Click here

    for Power Seat:

    Click here

  4. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH

    for Manual Seat:

    Click here

    for Power Seat:

    Click here

  5. INSTALL FRONT SEAT INNER CUSHION SHIELD LH

    for Manual Seat:

    Click here

    for Power Seat:

    Click here

  6. INSTALL FRONT SEAT CUSHION SHIELD LH

    for Manual Seat:

    Click here

    for Power Seat:

    Click here

  7. INSTALL FRONT SEAT INNER NO. 1 CUSHION SHIELD LH (for Power Seat)

    Click here

  8. INSTALL POWER SEAT SWITCH KNOB LH (for Reclining, for Power Seat)

    Click here

  9. INSTALL POWER SEAT SWITCH KNOB LH (for Slide and Vertical, Lifter, for Power Seat)

    Click here

  10. INSTALL VERTICAL ADJUSTING HANDLE LH (for Manual Seat)

    Click here

  11. INSTALL RECLINING ADJUSTER RELEASE HANDLE LH (for Manual Seat)


    1. A01SIVXC01
      B0069FO Install in this Direction

      With the reclining adjuster release handle LH pulled up.

    2. Push in the installation direction shown in the illustration and attach the claw to install the reclining adjuster release handle LH.

  12. INSTALL FRONT SEAT HEADREST ASSEMBLY

    for Manual Seat:

    Click here

    for Power Seat:

    Click here

  13. INSTALL FRONT SEAT ASSEMBLY LH

    for Manual Seat:

    Click here

    for Power Seat:

    Click here