ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System) DATA LIST / ACTIVE TEST

  1. READ DATA LIST

    Tip:

    Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Immobiliser / Data List.

    5. According to the display on the intelligent tester, read the "Data List".

      Table 1. Immobiliser

      Tester Display

      Measurement Item/Range

      Normal Condition

      Diagnostic Note

      Key SW

      Unlock warning switch signal / ON or OFF

      ON: Key inserted in ignition key cylinder

      OFF: No key in ignition key cylinder

      -

      IG SW

      Ignition switch signal / ON or OFF

      ON: Ignition switch ON

      OFF: Ignition switch ACC or off

      -

      Immobiliser

      Immobiliser system status / Set or Unset

      Set: No key in ignition key cylinder

      Unset: Key inserted in ignition key cylinder

      -

      Permit (Start)

      Permit (start) signal / OK or NG

      OK: Engine start permitted

      NG: Engine start not permitted

      -

      Response

      Transponder chip data / OK or NG

      OK: Data OK

      NG: Data error

      -

      Frame Error

      Transponder chip data / OK or NG

      OK: Data OK

      NG: Data error

      -

      Different Serial Number

      Transponder chip data / OK or NG

      OK: Data OK

      NG: Data error

      -

      Different Encrypt Code

      Transponder chip data / OK or NG

      OK: Data OK

      NG: Data error

      -

      Abnormal Status

      Transponder chip data / OK or NG

      OK: Data OK

      NG: Data error

      -

      BCC Malfunction

      Transponder chip signal / OK or NG

      OK: Correct data sent

      NG: Incorrect data sent

      -

      Sub Key

      Sub-key code signal / Reg or Unreg

      Reg: Registered sub-key code sent

      Unreg: Unmatching sub-key code sent

      -

      Master Key

      Master key code signal / Reg or Unreg

      Reg: Registered master key code sent

      Unreg: Unmatching master key code sent

      -

      Transponder S-code

      Number of registered sub-keys / min.: 0, max.: 15

      Number of registered sub-keys

      -

      Transponder M-code

      Number of registered master keys / min.: 0, max.: 15

      Number of registered master keys

      -

      Reg Code Space Full

      Key registration code memory space full / YES or NO

      NO: Possible to register more key codes

      YES: Cannot register any more key codes

      -

      +B

      +B judgment / Normal or Break

      Normal: Battery power supply normal

      Break: Battery power supply malfunctioning

      -

      Antenna Coil Status

      Antenna coil condition / Normal or Fail

      Normal: Antenna coil normal

      Fail: Antenna coil malfunctioning

      -

  2. PERFORM ACTIVE TEST

    Tip:

    Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Immobiliser / Active Test.

    5. Perform the Active Test according to the display on the intelligent tester.

      Table 2. Immobiliser

      Tester Display

      Test Part

      Control Range

      Diagnostic Note

      Security Indicator

      Security indicator light

      ON/OFF

      -