SFI SYSTEM, Diagnostic DTC:P0365, P0367, P0368

DTC Code DTC Name
P0365 Camshaft Position Sensor "B" Circuit (Bank 1)
P0367 Camshaft Position Sensor "B" Circuit Low Input (Bank 1)
P0368 Camshaft Position Sensor "B" Circuit High Input (Bank 1)

DESCRIPTION

The camshaft position sensor (for the exhaust camshaft) (EV1 signal) consists of a magnet and MRE (Magneto Resistance Element).

The exhaust camshaft has a timing rotor for the camshaft position sensor. When the exhaust camshaft rotates, changes occur in the air gaps between the timing rotor and MRE, which affects the magnetic field. As a result, the resistance of the MRE material fluctuates. The camshaft position sensor converts the camshaft rotation data to pulse signals, uses the pulse signals to determine the camshaft angle, and sends it to the ECM. Then the ECM uses this data to control fuel injection duration, fuel injection timing and the Variable Valve Timing (VVT) system.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0365 Camshaft Position Sensor "B" Circuit (Bank 1) No exhaust camshaft position sensor signal for 5 seconds at an engine speed of 600 rpm or higher (1 trip detection logic).

  • Open or short in camshaft position sensor (for exhaust camshaft) circuit

  • Camshaft position sensor (for exhaust camshaft)

  • Exhaust camshaft

  • Valve timing

  • ECM

 Comes on DTC stored
P0367 Camshaft Position Sensor "B" Circuit Low Input (Bank 1) The output voltage of the exhaust camshaft position sensor is less than 0.3 V for 4 seconds (1 trip detection logic).

  • Open or short in camshaft position sensor (for exhaust camshaft) circuit

  • Camshaft position sensor (for exhaust camshaft)

  • ECM

 Comes on DTC stored
P0368 Camshaft Position Sensor "B" Circuit High Input (Bank 1) The output voltage of the exhaust camshaft position sensor is higher than 4.7 V for 4 seconds (1 trip detection logic).

  • Open or short in camshaft position sensor (for exhaust camshaft) circuit

  • Camshaft position sensor (for exhaust camshaft)

  • ECM

 Comes on DTC stored

Tech Tips

Reference: Inspection using an oscilloscope.

Click here

MONITOR DESCRIPTION

If no pulse signal is transmitted by the camshaft position sensor (for exhaust camshaft) despite the camshaft rotating, the ECM interprets this as a malfunction of the sensor.

MONITOR STRATEGY

Required Sensors/Components (Main) Exhaust camshaft position sensor
Required Sensors/Components (Related) Crankshaft position sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN


  1. Connect the GTS to the DLC3.

  2. Turn the power switch on (IG) and turn the GTS on.

  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

  4. Turn the power switch off and wait for at least 30 seconds.

  5. Turn the power switch on (IG) and turn the GTS on.

  6. Put the engine in inspection mode (maintenance mode).

    Click here

  7. Start the engine.

  8. Idle the engine for 10 seconds or more.

  9. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  10. Read the pending DTCs.

    Tech Tips


    • If a pending DTC is output, the system is malfunctioning.

    • If a pending DTC is not output, perform the following procedure.

  11. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  12. Input the DTC: P0365, P0367 or P0368.

  13. Check the DTC judgment result.

    GTS Display Description
    NORMAL

    • DTC judgment completed

    • System normal
    ABNORMAL

    • DTC judgment completed

    • System abnormal
    INCOMPLETE

    • DTC judgment not completed

    • Perform driving pattern after confirming DTC enabling conditions
    N/A

    • Unable to perform DTC judgment

    • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    Tech Tips


    • If the judgment result shows NORMAL, the system is normal.

    • If the judgment result shows ABNORMAL, the system has a malfunction.

    • If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.

WIRING DIAGRAM

B008GC7E67

CAUTION / NOTICE / HINT

Tech Tips


  • Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

  • If no problem is found through this diagnostic troubleshooting procedure, there may be a mechanical problem with the engine.

PROCEDURE


  1. CHECK TERMINAL VOLTAGE (POWER SOURCE OF CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT))


    1. B008GG3C56
      *a

      Front view of wire harness connector

      (to Camshaft Position Sensor (for Exhaust Camshaft))

      Disconnect the camshaft position sensor (for exhaust camshaft) connector.

    2. Turn the power switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      F32-3 (VC2) - Body ground Power switch on (IG) 4.5 to 5.5 V
      Result
      Proceed to
      OK
      NG

    NG

    CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT) - ECM) Click here

    OK

  2. CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT) - ECM)


    1. Disconnect the camshaft position sensor (for exhaust camshaft) connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F32-1 (VVE+) - F6-81 (EV1+) Always Below 1 Ω
      F32-2 (VVE-) - F6-112 (EV1-) Always Below 1 Ω
      F32-1 (VVE+) or F6-81 (EV1+) - Body ground and other terminals Always 10 kΩ or higher
      F32-2 (VVE-) or F6-112 (EV1-) - Body ground and other terminals Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. CHECK SENSOR INSTALLATION (CAMSHAFT POSITION SENSOR FOR EXHAUST CAMSHAFT)


    1. B008GF8C01
      *a Clearance

      Check the camshaft position sensor (for exhaust camshaft) installation.

      OK
      Camshaft position sensor is installed correctly.
      Result
      Proceed to
      OK
      NG

    NG

    SECURELY REINSTALL CAMSHAFT POSITION SENSOR Click here

    OK

  4. INSPECT EXHAUST CAMSHAFT (TIMING ROTOR)


    1. Check the timing rotor of the exhaust camshaft.

      OK
      Camshaft timing rotor does not have any cracks or deformation.

      Tech Tips

      Perform "Inspection After Repair" after replacing the exhaust camshaft.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE EXHAUST CAMSHAFT Click here

    OK

  5. CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)


    1. Remove the cylinder head cover sub-assembly.

      B008GI8C05
      *a Timing Mark *b 7.43°
      *c 32.45° - -

    2. Turn the crankshaft pulley and align its groove with the "0" timing mark of the timing chain cover.

    3. Check that the timing marks of the camshaft timing gear assembly and camshaft timing exhaust gear assembly are at the positions shown in the illustration.

      Tech Tips

      If the timing marks are not as shown, turn the crankshaft one revolution clockwise.

      OK
      Timing marks on camshaft timing gear assembly and camshaft timing exhaust gear assembly are aligned as shown in the illustration.

      Tech Tips

      If the result is not as specified, check for mechanical malfunctions that may have affected the valve timing, such as a jumped tooth or stretching of the timing chain.

      Result
      Proceed to
      OK
      NG

    NG

    CHECK ENGINE MECHANICAL SYSTEM Click here

    OK

  6. REPLACE CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT)


    1. Replace the camshaft position sensor (for exhaust camshaft).

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  7. CHECK WHETHER DTC OUTPUT RECURS (DTC P0365, P0367 OR P0368)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Clear the DTCs.


      Powertrain > Engine and ECT > Clear DTCs

    5. Turn the power switch off and wait for at least 30 seconds.

    6. Turn the power switch on (IG).

    7. Turn the GTS on.

    8. Put the engine in inspection mode (maintenance mode).

      Click here


      Powertrain > Hybrid Control > Utility
      Tester Display
      Inspection Mode

    9. Start the engine and warm it up.

    10. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

    11. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    12. Read the DTCs.


      Powertrain > Engine and ECT > Trouble Codes
      Result
      Result Proceed to
      DTC P0365, P0367 or P0368 is output A
      DTCs are not output B

      Tech Tips

      If the engine does not start, replace the ECM.


    A

    REPLACE ECM Click here

    B

    END

  8. CHECK ENGINE MECHANICAL SYSTEM


    1. Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain.

      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

    OK

  9. CHECK WHETHER DTC OUTPUT RECURS (DTC P0365, P0367 OR P0368)


    1. Connect the GTS to the DLC3.

    2. Clear the DTCs.


      Powertrain > Engine and ECT > Clear DTCs

    3. Turn the power switch off and wait for at least 30 seconds.

    4. Turn the power switch on (IG).

    5. Turn the GTS on.

    6. Turn the power switch on (IG).

    7. Turn the GTS on.

    8. Put the engine in inspection mode (maintenance mode).

      Click here


      Powertrain > Hybrid Control > Utility
      Tester Display
      Inspection Mode

    9. Start the engine and warm it up.

    10. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

    11. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.

    12. Read the pending DTCs.


      Powertrain > Engine and ECT > Trouble Codes
      Result
      Result Proceed to
      DTCs are not output A
      DTC P0365, P0367 or P0368 is output B

    A

    CHECK FOR INTERMITTENT PROBLEMS Click here

    B

    REPLACE ECM Click here

  10. CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT) - ECM)


    1. Disconnect the camshaft position sensor (for exhaust camshaft) connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F32-3 (VC2) - F6-111 (VCE1) Always Below 1 Ω
      F32-3 (VC2) or F6-111 (VCE1) - Body ground and other terminals Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE ECM Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR