CAN COMMUNICATION SYSTEM(for LHD) Center Airbag Sensor Communication Stop Mode

DTC Code DTC Name
Center Airbag Sensor Communication Stop Mode

DESCRIPTION

Detection Item

Symptom

Trouble Area

Center Airbag Sensor Communication Stop Mode

Either condition is met:

  • "Airbag" is not displayed on "CAN Bus Check".

    Click here

  • Communication system DTCs (DTCs that start with U) that are output correspond to "Center Airbag Sensor Communication Stop Mode" in "DTC Combination Table".

    Click hereClick hereClick here

  • Power source or inside airbag sensor assembly

  • Airbag sensor assembly CAN branch wire or connector

  • Airbag sensor assembly

WIRING DIAGRAM

C279373E01

CAUTION / NOTICE / HINT

Note:

  • Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

    Click here

  • Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

  • After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

    Click hereClick hereClick here

  • Inspect the fuses for circuits related to this system before performing the following inspection procedure.

  • DTC check procedure: Turn the ignition switch to ON and wait at least 20 seconds.

  • After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

    Click hereClick hereClick here

  • The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the Precaution in the SRS.

    w/o Occupant Classification System:Click here

    w/ Occupant Classification System:Click here

Tip:

  • Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

  • Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

PROCEDURE

  1. CHECK FOR OPEN IN CAN BUS WIRE (AIRBAG SENSOR ASSEMBLY CAN BRANCH WIRE)

    1. C210016C04

      *a

      Rear view of wire harness connector

      (to Airbag Sensor Assembly)

      Disconnect the cable from the negative (-) battery terminal and wait for at least 90 seconds.

    2. Disconnect the airbag sensor assembly connector.

      Click here

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      G92-13 (CANH) - G92-22 (CANL)

      Cable disconnected from negative (-) battery terminal

      54 to 69 Ω

    Result

    Proceed to

    OK

    NG
    NG

    REPAIR OR REPLACE AIRBAG SENSOR ASSEMBLY CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

    OK

  2. CHECK HARNESS AND CONNECTOR (AIRBAG SENSOR ASSEMBLY - BATTERY AND BODY GROUND)

    1. C210016C05

      *a

      Rear view of wire harness connector

      (to Airbag Sensor Assembly)

      Connect the cable to the negative (-) battery terminal.

      Note:

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

      Click hereClick hereClick hereClick here

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection

      Switch Condition

      Specified Condition

      G92-21 (IG2) - Body ground

      Ignition switch ON

      11 to 14 V

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      G92-25 (E1) - Body ground

      Always

      Below 1 Ω

      G92-26 (E2) - Body ground

      Always

      Below 1 Ω

    Result

    Proceed to

    OK

    NG
    OK

    REPLACE AIR BAG SENSOR ASSEMBLY

    Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR