CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM, Diagnostic DTC:P1585

DTC Code DTC Name
P1585 Acceleration Sensor Circuit

DESCRIPTION

The ECM determines the vehicle inclination based on a signal from the yaw rate and acceleration sensor (airbag sensor assembly).

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

Memory

P1585

Acceleration Sensor Circuit

1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other

  1. The ignition switch is ON.

  2. The output value of the yaw rate and acceleration sensor remains at -1.5 G or less, or 1.5 G or more for at least 1.2 seconds.

  3. 0.5 seconds

  4. 1 trip detection logic

  1. The ignition switch is ON.

  2. The power source voltage to the yaw rate and acceleration sensor remains at 4.4 V or less, or 5.6 V or higher for at least 1.2 seconds.

  3. 0.5 seconds

  4. 1 trip detection logic

  1. The ignition switch is ON.

  2. No signal from the yaw rate and acceleration sensor is detected 7 times or more.

  3. 0.5 seconds

  4. 1 trip detection logic

  1. The ignition switch is ON.

  2. With the vehicle stopped, the difference between GL1 and GL2 does not become less than 0.4 G within 60 seconds after exceeding 0.6 G.

  3. 0.5 seconds

  4. 1 trip detection logic

  1. The ignition switch is ON.

  2. A yaw rate and acceleration sensor power source voltage malfunction signal is received for at least 10 seconds with the vehicle speed at 3 km/h (1.8 mph) or more.

  3. 0.5 seconds

  4. 1 trip detection logic

  • Yaw rate and acceleration sensor (Airbag sensor assembly)

  • Skid control ECU (Brake actuator assembly)

  • CAN communication system

-

DTC stored

WIRING DIAGRAM

C347476E01

CAUTION / NOTICE / HINT

Note:

  • Perform initialization when parts related to the continuously variable transaxle are replaced.

    Click here

  • Check that no DTCs are stored after performing initialization.

    Click here

Tip:

If a CAN communication DTC is output, perform troubleshooting for that DTC first.

PROCEDURE

  1. CHECK DTC OUTPUT (CAN COMMUNICATION SYSTEM)

    1. Check for DTCs of the CAN communication system.

      Result

      Proceed to

      DTCs are not output

      DTCs are output
    DTCs are output

    GO TO CAN COMMUNICATION SYSTEM (DIAGNOSIS SYSTEM)

    DTCs are not output

  2. READ VALUE USING GTS (G SENSOR)

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine and ECT / Data List.

      Powertrain > Engine and ECT > Data List

      Tester Display

      G Sensor

      Powertrain > Engine and ECT > Data List

      Tester Display

      Measurement Item

      Range

      Normal Condition

      Diagnostic Note

      G Sensor

      Converted output voltage of deceleration sensor

      min.: 0 V

      max.: 79.998 V

      Displays converted voltage of deceleration sensor

      • Vehicle on level ground: 2.31 V to 2.69 V

      • Decelerating: 1.88 V to 2.5 V

      • Accelerating: 2.5 V to 3.11 V

      • G sensor malfunction: Set to 1.87 V

      • Communication malfunction: Set to 1.87 V

      -

    5. In accordance with the display on the GTS, read the Data List.

      Result

      Result

      Proceed to

      Data displayed is as specified under Normal Condition

      A

      Data displayed is not as specified under Normal Condition

      B
    A

    REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

    Click hereClick here

    B

  3. REPLACE YAW RATE AND ACCELERATION SENSOR (AIRBAG SENSOR ASSEMBLY)

    1. Replace the yaw rate and acceleration sensor (airbag sensor assembly).

      Click here

    Result

    Proceed to

    NEXT
    NEXT

    PERFORM INITIALIZATION

    Click here