QUARTER WINDOW GLASS REMOVAL

CAUTION / NOTICE / HINT

PROCEDURE

1. PRECAUTION

   Note:

   After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

   Click hereClick here

2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

   Note:

   When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

   Click hereClick here

3. REMOVE PACKAGE TRAY TRIM POCKET SUB-ASSEMBLY (w/ Partition Net)

   Click here

4. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)

   Click here

5. REMOVE DECK BOARD ASSEMBLY (w/o Spare Tire)

   Click here

6. REMOVE REAR NO. 3 FLOOR BOARD

   Click here

7. REMOVE REAR NO. 2 FLOOR BOARD

   Click here

8. REMOVE DECK BOARD ASSEMBLY (for Full Size Spare Tire)

   Click here

9. REMOVE DECK FLOOR BOX LH

   Click here

10. REMOVE REAR FLOOR FINISH PLATE (w/o Spare Tire, for Compact Spare Tire)

    Click here

11. REMOVE REAR DECK TRIM COVER (for Full Size Spare Tire)

    Click here

12. REMOVE REAR NO. 1 FLOOR MAT SUPPORT SIDE PLATE (w/o Spare Tire)

    Click here

13. REMOVE REAR NO. 1 FLOOR MAT SUPPORT SIDE PLATE (for Full Size Spare Tire)

    Click here

14. REMOVE REAR SEAT ASSEMBLY

    Click here

15. REMOVE REAR DOOR SCUFF PLATE LH

    Click here

16. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

    Click here

17. REMOVE SEAT BELT ANCHOR COVER CAP

    Click here

18. REMOVE DECK TRIM SERVICE HOLE COVER

    Click here

19. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH

    Click here

20. REMOVE INNER ROOF SIDE GARNISH ASSEMBLY LH

    Click here

21. REMOVE ROOF HEADLINING ASSEMBLY

    1. Partially remove the roof headlining assembly.

       Click here

       Tip:

       It is not necessary to completely remove the roof headlining assembly. Slightly lower the rear section of the roof headlining assembly so that the quarter window glass assembly LH can be removed.

22. REMOVE QUARTER WINDOW ASSEMBLY LH

    

    *1	Protective Tape

    Tip:

    Apply protective tape to the outer surface of the vehicle body to prevent scratches.

    Note:

    When separating the quarter window assembly from the vehicle, be careful not to damage the vehicle paint or interior/exterior ornaments.

    1. Using a knife, cut off the moulding as shown in the illustration.

       Note:

       Be careful not to damage the vehicle body.

       

       *a

       Cut

       -

       -

    2. Disconnect the connector.

    3. From the interior, insert a piano wire between the vehicle body and the quarter window assembly as shown in the illustration.

    4. Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.

    5. 

       *1	Wire
       *2	Clip

       Cut through the adhesive by pulling the piano wire around the quarter window glass.

       Note:

       Leave as much adhesive on the vehicle body as possible when removing the quarter window assembly.

    6. Using suction cups, remove the quarter window assembly LH.

       Tip:

       • Be careful not to drop the quarter window assembly.

       • Be sure to replace the quarter window assembly with a new one.

23. CLEAN VEHICLE BODY

    

    *1	Adhesive
    *2	Vehicle Body

    1. Clean and shape the contact surface of the vehicle body.

       1. On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.

          Tip:

          Leave as much adhesive on the vehicle body as possible.

          Note:

          Be careful not to damage the vehicle body.

       2. Clean the contact surface of the vehicle body with cleaner.

          Tip:

          Even if all the adhesive has been removed, clean the vehicle body.