SFI SYSTEM Brake Override System

DTC Code	DTC Name
	Brake Override System

DESCRIPTION

When the vehicle is being driven, depressing the accelerator pedal sensor assembly and brake pedal will activate the brake override system to restrict driving torque. The conditions for activating the brake override system as well as the items that are controlled are explained below.

Activation Conditions:

When the accelerator pedal and brake pedal are depressed.

Note:
The vehicle may not enter the brake override system control due to the relation of the accelerator pedal angle and the vehicle's speed.

Items Controlled:

When the vehicle speed is extremely low, the accelerator opening value used when controlling the engine is reduced more than normal.

Tip:
During control, the Accelerator Position value in the Data List will be lower than normal.
When the vehicle speed is not extremely low, the accelerator opening value is forcibly lowered to a fixed value.

Tip:
During control, the Accelerator Position value in the Data List is forcibly reduced to a specified value regardless of the actual accelerator opening value (Accelerator Position Sensor No.1 Voltage %).

Deactivation Conditions:

When the brake pedal or the accelerator pedal returns to some degree.

CAUTION / NOTICE / HINT

Inspection Method

Example:

Drive at 10 km/h (6.25 mph), depress the accelerator pedal by 1/2 to 3/4 and keep it in that position. Under these conditions, if the engine speed decreases to 1000 rpm when the brake pedal is depressed, then the brake override system has been activated.

CAUTION:

When carrying out the inspection, use a place where you are able to carry it out safely and also pay close attention to your surroundings.

Also, when driving make absolutely sure that all road traffic laws, such as speed limits, are observed.

Tip:

Under normal conditions, the Accelerator Position value changes in response to the Accelerator Position Sensor No.1 Voltage % value. For more information on the numerical values, refer to the Data List.
Click here Click here
If the Accelerator Position and Accelerator Position Sensor No.1 Voltage % values in the Data List diverge and the Accelerator Position value in the Data List is fixed even though Accelerator Position Sensor No.1 Voltage % is changing, check that this control is activated (use the GTS data saving function to record data while driving the vehicle and then confirm it after driving is completed).

Note:

The brake override system restricts driving torque if the brake pedal is depressed when driving with the accelerator pedal depressed. If a customer reports experiencing loss of torque after the accelerator and brake pedals have both been intentionally depressed, explain to the customer that this is not a malfunction, and that the customer should avoid depressing both the accelerator and brake pedals at the same time.

Example: While operating the accelerator pedal, the customer uses their left foot to operate the brake pedal.

PROCEDURE

CHECK DTC OUTPUT

Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: System Select / Health Check.
Check the DTCs.

Result


Result	Proceed to
DTCs are not output	A
DTCs are output	B

GO TO DTC CHART

READ VALUE USING GTS (MASTER CYLINDER SENSOR)

Connect the GTS to the DLC3.
Start the engine and turn the GTS on.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List / Master Cylinder Sensor.

Chassis > ABS/VSC/TRC > Data List


Tester Display
Master Cylinder Sensor

Read the value displayed on the GTS.


GTS Display	Measurement Item/Range	Normal Condition
Master Cylinder Sensor	Master cylinder pressure sensor reading/ Min.: 0.00 V, Max.: 5.00 V	Brake pedal released: 0.20 to 0.40 V Reading increases when brake pedal is depressed

Check that the brake fluid pressure value of the "Master Cylinder Sensor" observed on the GTS changes when the brake pedal is depressed.

OK

When the pedal is depressed, the voltage displayed on the GTS increases.

Result


Proceed to
OK
NG

CHECK BRAKE ACTUATOR ASSEMBLY

Click here

READ VALUE USING GTS (STOP LIGHT SW)

Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.

Enter the following menus: Powertrain / Engine / Data List / All Data / Stop Light SW.

Powertrain > Engine > Data List


Tester Display
Stop Light SW

Check the Data List indication when the brake pedal is depressed and released.


GTS Display	Condition	Specified Condition
Stop Light SW	Brake pedal released	OFF
Stop Light SW	Brake pedal depressed	ON

Result


Proceed to
OK
NG

INSPECT STOP LIGHT SWITCH ASSEMBLY

Click here Click here

INSPECT BRAKE PEDAL SUPPORT SUB-ASSEMBLY

Inspect and adjust the brake pedal support sub-assembly.
for RHD:Click here
for LHD:Click here Click here

Tip:
If the stop light switch turns ON too late, the start of brake override system control may be delayed; if it turns ON too soon, brake override system control may begin too early, so conduct inspection of the brake pedal support assembly and stop light switch assembly.

Result


Proceed to
OK
NG

REPAIR OR REPLACE BRAKE PEDAL SUPPORT SUB-ASSEMBLY

for RHD:Click here

for LHD:Click here

READ VALUE USING GTS (ACCELERATOR PEDAL POSITION SENSOR)

Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.

Enter the following menus: Powertrain / Engine / Data List / All Data / Accelerator Position Sensor No.1 Voltage % and Accelerator Position Sensor No.2 Voltage %.

Powertrain > Engine > Data List


Tester Display
Accelerator Position Sensor No.1 Voltage %
Accelerator Position Sensor No.2 Voltage %

Read the value displayed on the GTS.


GTS Display	Condition	Specified Condition
Accelerator Position Sensor No.1 Voltage %	Accelerator Pedal Released → Depressed → Released	Values smoothly change following accelerator pedal operation
Accelerator Position Sensor No.2 Voltage %	Accelerator Pedal Released → Depressed → Released

Tip:

For numerical values of Accelerator Position Sensor No.1 Voltage % and Accelerator Position Sensor No.2 Voltage %, refer to the Data List.

Click here Click here

Result


Proceed to
OK
NG

REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY

Click here

READ VALUE USING GTS (VEHICLE SPEED)

Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Start the engine.

Enter the following menus: Powertrain / Engine / Data List / All Data / Vehicle Speed.

Powertrain > Engine > Data List


Tester Display
Vehicle Speed

Read the value displayed on the GTS.

Standard


GTS Display	Condition	Specified Condition
Vehicle Speed	Vehicle stopped, engine running	0 km/h (0 mph)
Vehicle Speed	Vehicle being driven at constant speed between 16.1 to 64.4 km/h (10 to 40 mph)	No large fluctuations when driving at a constant speed

CAUTION:

When performing a drive test, obey all speed limits and traffic laws.

Tip:

Data can be captured relatively easily by using the snapshot function in the Data List. Confirm the data after performing the drive test.

Result


Proceed to
OK
NG

GO TO METER / GAUGE SYSTEM (SPEED SIGNAL CIRCUIT)

Click here Click here Click here Click here

READ VALUE USING GTS (FR, FL, RR, RL WHEEL SPEED)

Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Start the engine.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List / FR Wheel Speed, FL Wheel Speed, RR Wheel Speed and RL Wheel Speed.

Chassis > ABS/VSC/TRC > Data List


Tester Display
FR Wheel Speed
FL Wheel Speed
RR Wheel Speed
RL Wheel Speed

Read the value displayed on the GTS.

Standard


GTS Display	Condition	Specified Condition
FR Wheel Speed FL Wheel Speed RR Wheel Speed RL Wheel Speed	Vehicle stopped, engine running	0 km/h (0 mph)
FR Wheel Speed FL Wheel Speed RR Wheel Speed RL Wheel Speed	Vehicle being driven at constant speed between 16.1 to 64.4 km/h (10 to 40 mph)	No large fluctuations when driving at a constant speed

CAUTION:

When performing a drive test, obey all speed limits and traffic laws.

Tip:

Data can be captured relatively easily by using the snapshot function in the Data List. Confirm the data after performing the drive test.

Result


Proceed to
OK
NG

END

INSPECT FRONT OR REAR SPEED SENSOR