BLACK OUT TAPE(for Rear Door) INSTALLATION

CAUTION / NOTICE / HINT

Tip:

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

  • A bolt without a torque specification is shown in the standard bolt chart.

    Click here

PROCEDURE

  1. REPAIR INSTRUCTION

    Click here

  2. INSTALL REAR DOOR LOWER OUTSIDE STRIPE LH

    Tip:

    When installing the rear door lower outside stripe, heat the rear door panel and rear door lower outside stripe using a heat light.

    Standard

    Item

    Temperature

    Rear Door Panel

    40 to 60°C (104 to 140°F)

    Rear Door Lower Outside Stripe

    20 to 30°C (68 to 86°F)
    Note:

    Do not heat the rear door panel or rear door lower outside stripe excessively.

    1. B340215E01

      Refer to the illustration to position a new rear door lower outside stripe.

      Reference Value

      Area

      Specified Condition

      A

      2 to 4 mm (0.0787 to 0.157 in.)

      B

      5 mm (0.1969 in.)

    2. Remove the release paper from the rear door lower outside stripe.

  3. INSTALL REAR DOOR OUTSIDE STRIPE LH

    Tip:

    When installing the rear door outside stripe, heat the rear door panel and rear door outside stripe using a heat light.

    Standard

    Item

    Temperature

    Rear Door Panel

    40 to 60°C (104 to 140°F)

    Rear Door Outside Stripe

    20 to 30°C (68 to 86°F)
    Note:

    Do not heat the rear door panel or rear door outside stripe excessively.

    1. B340217E01

      Refer to the illustration to position a new rear door outside stripe.

      Reference Value

      Area

      Specified Condition

      A

      2 to 4 mm (0.0787 to 0.157 in.)

      B

      5 mm (0.1969 in.)

      C

      1.5 to 2.5 mm (0.0591 to 0.0984 in.)

    2. Remove the release paper from the rear door outside stripe.

  4. INSTALL DOOR WINDOW FRAME MOULDING CLIP

    Click here

  5. INSTALL REAR DOOR OUTSIDE MOULDING SUB-ASSEMBLY LH

    Click here

  6. INSTALL REAR DOOR WEATHERSTRIP LH

    Click here

  7. INSTALL REAR DOOR BELT MOULDING ASSEMBLY LH

    Click here

  8. INSTALL REAR DOOR GLASS SUB-ASSEMBLY LH

    Click hereClick here

  9. INSTALL REAR DOOR QUARTER WINDOW GLASS LH

    Click hereClick here

  10. INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH

    Click hereClick here

  11. INSTALL REAR DOOR GLASS RUN LH

    Click hereClick here

  12. INSTALL REAR DOOR SERVICE HOLE COVER LH

    Click hereClick here

  13. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

    Click hereClick here

  14. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG LH

    Click hereClick here

  15. INSTALL DOOR ASSIST GRIP COVER LH

    Click hereClick here

  16. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL

    Click hereClick here

  17. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click hereClick hereClick hereClick hereClick hereClick here

  18. CHECK POWER WINDOW CONTROL SYSTEM

    1. w/ Jam Prptection Function:

      Click hereClick here

    2. w/o Jam Prptection Function:

      Click here