ROOF HEADLINING (for Single Cab) INSTALLATION

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.


  1. INSTALL REAR NO. 2 SIDE RAIL SPACER LH


    1. Attach the 2 claws to install the rear No. 2 side rail spacer.

  2. INSTALL REAR NO. 2 SIDE RAIL SPACER RH

    Tech Tips

    Use the same procedure described for the LH side.

  3. INSTALL SIDE RAIL SPACER (for LHD)


    1. Attach the 2 claws to install the side rail spacer.

  4. INSTALL SIDE RAIL SPACER (for RHD)

    Tech Tips

    Use the same procedure described for the LHD.

  5. INSTALL FRONT SIDE RAIL SPACER LH


    1. Attach the 2 claws to install the front side rail spacer.

  6. INSTALL FRONT SIDE RAIL SPACER RH

    Tech Tips

    Use the same procedure described for the LH side.

  7. INSTALL ROOF HEADLINING ASSEMBLY


    1. for LHD:


      1. A01DZ4M

        Place the roof headlining into the vehicle as shown in the illustration.

        Note

        Be careful not to damage the roof headlining when placing it.

      2. Install the roof headlining with the 5 clips.

      3. Connect the connectors and attach the 4 clamps.

    2. for RHD:


      1. A01DWKM

        Place the roof headlining into the vehicle as shown in the illustration.

        Note

        Be careful not to damage the roof headlining when placing it.

      2. A01DYA4E01
        Text in Illustration
        *A w/o Assist Grip

        Install the roof headlining with the clips.

      3. Connect the connectors and attach the 5 clamps.

    3. Attach the 4 clamps to the front pillar.

  8. INSTALL DEFROSTER NOZZLE ASSEMBLY (w/ Defroster)


    1. Attach the 4 clips to install the defroster nozzle assembly.

  9. INSTALL NO. 3 HEATER TO REGISTER DUCT


    1. Attach the 4 claws to install the No. 3 heater to register duct.

    2. Install the clip.

  10. INSTALL NO. 1 HEATER TO REGISTER DUCT


    1. Attach the 3 claws to install the No. 1 heater to register duct.

    2. Install the clip.

  11. INSTALL NO. 2 HEATER TO REGISTER DUCT


    1. Install the No. 2 heater to register duct with the 3 clips.

  12. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY


    1. Attach the 3 guides, 2 claws and 3 clips to install the lower instrument panel finish panel.

  13. INSTALL UPPER INSTRUMENT PANEL SUB-ASSEMBLY

    Click here

  14. INSTALL ASSIST GRIP (w/ Assist Grip)


    1. Install the assist grip with the 2 screws.

    2. Attach the 4 claws to close the 2 covers.

  15. INSTALL VISOR HOLDER LH


    1. Attach the 2 claws to install the visor holder.

    2. Install the screw.

  16. INSTALL VISOR HOLDER RH

    Tech Tips

    Use the same procedure described for the LH side.

  17. INSTALL VISOR ASSEMBLY LH


    1. Install the visor with the 2 screws.

    2. Attach the guide.

  18. INSTALL VISOR ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  19. INSTALL NO. 1 ROOM LIGHT ASSEMBLY

    A01DYEV

    1. Connect the light connector.

    2. Install the room light with the 2 screws.

    3. A01E0U3E01

      Attach the lens with the 4 claws.

  20. INSTALL QUARTER INSIDE TRIM BOARD LH


    1. Attach the 3 clips to install the quarter inside trim board.

    2. Connect the front seat belt shoulder anchor with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    3. Attach the 2 claws to close the front seat belt shoulder anchor cover.

  21. INSTALL QUARTER INSIDE TRIM BOARD RH

    Tech Tips

    Use the same procedure described for the LH side.

  22. INSTALL LOWER QUARTER TRIM PANEL LH


    1. Attach the 3 clips, claw and 2 guides to install the lower quarter trim panel.

    2. Connect the front seat outer belt floor anchor with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  23. INSTALL LOWER QUARTER TRIM PANEL RH

    Tech Tips

    Use the same procedure described for the LH side.

  24. INSTALL UPPER BACK PANEL GARNISH


    1. Attach the 5 clips, 4 guides and 4 claws to install the upper back panel garnish.

  25. INSTALL FRONT PILLAR GARNISH LH


    1. w/ Curtain Shield Airbag:


      1. Remove the protective cover.

    2. Attach the 2 guides and 2 clips to install the front pillar garnish.

  26. INSTALL FRONT PILLAR GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  27. INSTALL FRONT ASSIST GRIP SUB-ASSEMBLY (w/ Assist Grip)

    Tech Tips

    Use the same procedure for both front assist grips.


    1. Install the front assist grip with the 2 screws.

  28. INSTALL FRONT NO. 1 ASSIST GRIP PLUG LH (w/ Assist Grip)

    Tech Tips

    Use the same procedure for both front No. 1 assist grip plug.


    1. Attach the 2 claws to install the front No. 1 assist grip plug.

  29. INSTALL FRONT NO. 1 ASSIST GRIP PLUG RH (w/ Assist Grip)

    Tech Tips

    Use the same procedure described for the LH side.

  30. INSTALL FRONT DOOR OPENING TRIM LH

    A01E27IE01
    Text in Illustration
    *1 Paint Mark
    *2 Mark Position

    1. Align the paint mark on the front door opening trim with the mark position on the vehicle and install the front door opening trim as shown in the illustration.

  31. INSTALL FRONT DOOR OPENING TRIM RH

    Tech Tips

    Use the same procedure described for the LH side.

  32. INSTALL FRONT DOOR SCUFF PLATE LH


    1. Attach the 4 clips and 8 claws to install the front door scuff plate.

  33. INSTALL FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure described for the LH side.

  34. INSTALL FRONT SEAT ASSEMBLY LH


    1. w/ Front Seat Side Airbag:

      Click here

    2. for Separate Seat Type:

      Click here

  35. INSTALL FRONT SEAT ASSEMBLY RH


    1. w/ Front Seat Side Airbag:

      Tech Tips

      Use the same procedure described for the LH side.

    2. for Separate Seat Type:

      Tech Tips

      Use the same procedure described for the LH side.

    3. for Bench Seat Type:

      Click here

  36. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (w/ Airbag System)

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  37. CHECK SRS WARNING LIGHT (w/ Airbag System)

    Click here