ROOF HEADLINING (for Full-trim) REMOVAL


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (- ) battery terminal notices before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE REAR NO. 1 SEAT ASSEMBLY


    1. for Fixed Seat Type:

      Remove the rear No. 1 seat assembly Click here.

    2. for Fold Down Seat Type:

      Remove the rear No. 1 seat assembly Click here.

    3. for Swiveling Seat Type:

      Remove the rear No. 1 seat assembly Click here.

    4. w/ Headrest:

      Remove the rear No. 1 seat assembly Click here.

    5. w/o Headrest:

      Remove the rear No. 1 seat assembly Click here.

  4. REMOVE REAR NO. 2 SEAT ASSEMBLY


    1. w/ Headrest:

      Remove the rear No. 2 seat assembly Click here.

    2. w/o Headrest

      Remove the rear No. 2 seat assembly Click here.

  5. REMOVE REAR NO. 3 SEAT ASSEMBLY


    1. for Bench Type Seatback:

      Remove the rear No. 3 seat assembly Click here.

    2. for Separate Type Seatback:

      Remove the rear No. 3 seat assembly Click here.

  6. REMOVE REAR NO. 4 SEAT ASSEMBLY

    Remove the rear No. 4 seat assembly Click here.

  7. REMOVE REAR SEAT BELT ASSEMBLY OUTER


    1. B007UGX

      Remove the bolt and disconnect the floor side of the rear seat belt assembly outer.

    2. B007UIK

      Using a screwdriver, detach the 4 claws and open the shoulder side cover of the rear seat belt assembly outer.

      Tech Tips

      Tape the screwdriver tip before use.

    3. B007PB8

      Loosen the bolt and disconnect the shoulder side of the rear seat belt assembly outer.

    4. B007W5L

      Loosen the bolt and remove the rear seat belt assembly outer.

    5. for Rear No. 1 Seat Bench Seat Type:


      1. B007WCI

        w/ Cover:

        Detach the 3 claws and 3 guides, and then remove the side trim cover.

      2. Loosen the bolt and disconnect the floor side of the rear seat belt assembly outer.

        B007QIJE01
        Text in Illustration
        *A w/o Cover *B w/ Cover
      3. B007SMA

        Using a screwdriver, detach the 2 claws and open the shoulder side cover of the rear seat belt assembly outer.

        Tech Tips

        Tape the screwdriver tip before use.

      4. B007OYJ

        Loosen the bolt and disconnect the shoulder side of the rear seat belt assembly outer.

      5. B007THD

        Loosen the bolt.

      6. Detach the 2 claws and remove the retractor cover of the rear seat belt assembly outer.

      7. B007QCN

        Remove the 2 bolts and rear seat belt assembly outer.

    6. w/ Cover:


      1. Remove the bolt from the floor side of the rear seat belt assembly outer.

      2. Remove the side trim cover from the rear seat belt assembly outer.

  8. REMOVE REAR NO. 2 SEAT BELT ASSEMBLY OUTER


    1. B007PJ7

      Remove the bolt and disconnect the floor side of the rear No. 2 seat belt assembly outer.

    2. B007TKK

      Using a screwdriver, detach the 2 claws and open the shoulder side cover of the rear No. 2 seat belt assembly outer.

      Tech Tips

      Tape the screwdriver tip before use.

    3. B007OV4

      Remove the bolt and disconnect the shoulder side of the rear No. 2 seat belt assembly outer.

    4. B007UC0

      Remove the bolt and rear No. 2 seat belt assembly outer.

  9. REMOVE REAR NO. 3 SEAT BELT ASSEMBLY OUTER


    1. B007THR

      Remove the bolt and disconnect the floor side of the rear No. 3 seat belt assembly outer.

    2. B007UIY

      Using a screwdriver, detach the 4 claws and open the shoulder side cover of the rear No. 3 seat belt assembly outer.

      Tech Tips

      Tape the screwdriver tip before use.

    3. B007RRF

      Loosen the bolt and disconnect the shoulder side of the rear No. 3 seat belt assembly outer.

    4. B007T4A

      Using a screwdriver, detach the 4 claws and remove the retractor cover of the rear No. 3 seat belt assembly outer.

      Tech Tips

      Tape the screwdriver tip before use.

    5. B007RLB

      Remove the bolt and rear No. 3 seat belt assembly outer.

  10. REMOVE REAR NO. 4 SEAT BELT ASSEMBLY OUTER


    1. B007VHO

      Remove the bolt and disconnect the floor side of the rear No. 4 seat belt assembly outer.

    2. B007PN1

      Using a screwdriver, detach the 2 claws and open the shoulder side cover of the rear No. 4 seat belt assembly outer.

      Tech Tips

      Tape the screwdriver tip before use.

    3. B007UMD

      Remove the bolt and disconnect the shoulder side of the rear No. 4 seat belt assembly outer.

    4. B007OJ7

      Using a screwdriver, detach the 4 claws and remove the retractor cover of the rear No. 4 seat belt assembly outer.

      Tech Tips

      Tape the screwdriver tip before use.

    5. B007QII

      Remove the bolt and rear No. 4 seat belt assembly outer.

  11. REMOVE FRONT DOOR SCUFF PLATE LH


    1. B007ORA

      Detach the 5 clips and remove the front door scuff plate LH.

  12. REMOVE FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedures described for the LH side.

  13. REMOVE FRONT DOOR OPENING TRIM LH

  14. REMOVE FRONT DOOR OPENING TRIM RH

  15. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH


    1. B007PGB

      Remove the bolt and disconnect front seat outer belt assembly RH.

    2. B007V6CE02
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, detach the 2 claws and open the cover.

      Tech Tips

      Tape the screwdriver tip before use.

    3. B007TQX

      Remove the bolt and disconnect front seat outer belt assembly RH.

  16. REMOVE CENTER PILLAR GARNISH COVER LOWER LH


    1. B007ROJE01

      Remove the clip.

    2. Using a screwdriver, detach the 4 clips and remove the center pillar garnish lower RH.

      Tech Tips

      Tape the screwdriver tip before use.

  17. REMOVE SEAT ASSEMBLY LH


    1. Disconnect connector.

    2. B007PCK

      Remove the nut and 3 bolts.

    3. Remove the seat assembly LH.

  18. REMOVE SEAT BELT ANCHOR COVER


    1. B007UUWE01

      Remove the 2 clips.

    2. Detach the claw and then remove the seat belt anchor cover.

  19. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH


    1. B007QB0

      Remove the bolt and disconnect the front seat outer belt assembly LH.

    2. B007Q86E02
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, detach the 2 claws and open the cover.

      Tech Tips

      Tape the screwdriver tip before use.

    3. B007RIY

      Remove the bolt and disconnect the front seat outer belt assembly LH.

  20. REMOVE REAR DOOR SCUFF PLATE RH


    1. B007SGI

      Detach the 11 clips and remove the rear door scuff plate RH.

  21. REMOVE SLIDE DOOR WEATHERSTRIP NO. 1 RH

  22. REMOVE BACK DOOR SCUFF PLATE


    1. B007U93E01

      Detach the 7 clips and 4 claws and remove the back door scuff plate.

  23. REMOVE BACK DOOR WEATHERSTRIP

  24. REMOVE QUARTER TRIM PANEL ASSEMBLY REAR LH (for Middle Roof)


    1. B007QTA

      Detach the 21 clips and remove the quarter trim panel assembly rear LH.

  25. REMOVE QUARTER TRIM PANEL ASSEMBLY REAR LH (for High Roof)


    1. B007T7W

      Detach the 35 clips and remove the quarter trim panel assembly rear LH.

  26. REMOVE QUARTER TRIM PANEL ASSEMBLY REAR RH

    Tech Tips

    Use the same procedures described for the LH side.

  27. REMOVE SIDE NO. 1 TRIM ASSEMBLY LH


    1. B007PS4

      Detach the 21 clips and remove the side No. 1 trim assembly LH.

  28. REMOVE ENGINE SERVICE HOLE COVER HOOK NO. 2 LH


    1. B007QNR

      Remove the screw and engine service hole cover hook No. 2 LH.

  29. REMOVE CENTER PILLAR GARNISH LH


    1. B007SMO

      Detach the 5 clips and 2 claws, and remove the center pillar garnish LH.

  30. REMOVE ASSIST GRIP PLUG


    1. B007PUH

      Using a screwdriver, detach the 4 claws and remove the 2 assist grip plugs.

      Tech Tips

      Tape the screwdriver tip before use.

  31. REMOVE ASSIST GRIP ASSEMBLY REAR


    1. B007W77

      Remove the 2 screws and assist grip assembly rear.

  32. REMOVE CENTER PILLAR GARNISH LOWER RH


    1. B007TYL

      Detach the 4 claws and remove the center pillar garnish lower RH.

  33. REMOVE CENTER PILLAR GARNISH RH


    1. B007VSK

      Detach the 3 clips, claw and remove the center pillar garnish RH.

  34. REMOVE QUARTER PILLAR GARNISH LH (for High Roof)


    1. B007QJOE02

      Detach the 6 clips and remove the quarter pillar garnish LH.

  35. REMOVE QUARTER PILLAR GARNISH RH (for High Roof)

    Tech Tips

    Use the same procedures described for the LH side.

  36. REMOVE QUARTER PILLAR GARNISH LH (for Middle Roof)


    1. B007VWV

      Detach the 3 clips and remove the quarter pillar garnish LH.

  37. REMOVE QUARTER PILLAR GARNISH RH (for Middle Roof)

    Tech Tips

    Use the same procedures described for the LH side.

  38. REMOVE ROOF SIDE GARNISH INNER UPPER LH


    1. B007REG

      Using a screwdriver, detach the 6 clips and remove the roof side garnish inner upper LH.

      Tech Tips

      Tape the screwdriver tip before use.

  39. REMOVE ROOF SIDE GARNISH INNER UPPER RH

    Tech Tips

    Use the same procedures described for the LH side.

  40. REMOVE REAR SEAT HOOK (for Space Up Seat)


    1. B007RE7

      Remove the bolt and rear seat hook.

  41. REMOVE ROOM LIGHT ASSEMBLY NO. 2 (Deluxe)


    1. B007OKZE03
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, detach the 4 claws and remove the room light lens cover.

      Tech Tips

      Tape the screwdriver tip before use.

    2. B007TVK

      Remove the 2 screws and room light assembly No. 2.

    3. Disconnect the connector.

  42. REMOVE ROOM LIGHT ASSEMBLY NO. 2 (Super Wagon)


    1. B007VZJ

      Using a screwdriver, detach the 4 claws and remove the room light base.

      Tech Tips

      Tape the screwdriver tip before use.

    2. Remove the 2 screws.

    3. B007S5CE01

      Pull the room light assembly No. 2 rearward and detach the 2 claws and remove it.

    4. Disconnect the connector.

  43. REMOVE ROOF HEADLINING NO. 2 (for Middle Roof)


    1. B007UPPE01

      Using a clip remover, remove the 19 clips.

    2. Using a clip remover, detach the clip A and remove the roof headlining No. 2.

  44. REMOVE ROOF HEADLINING NO. 2 (for High Roof)

    B007OG8E01

    1. Using a clip remover, remove the 25 clips.

    2. Using a clip remover, detach the clip A and remove the roof headlining No. 2.

  45. REMOVE FRONT ASSIST GRIP PLUG NO. 1


    1. B007RBZ

      Using a screwdriver, detach the 4 claws and remove the 2 front assist grip plugs No. 1.

      Tech Tips


      • Tape the screwdriver tip before use.

      • Use the same procedures described for the other side.

  46. REMOVE ASSIST GRIP ASSEMBLY


    1. B007RGJ

      Remove the 2 screws and assist grip assembly.

      Tech Tips

      Use the same procedures described for the other side.

  47. REMOVE FRONT PILLAR GARNISH LH


    1. B007Q53

      Detach the clip and claw and remove the front pillar garnish LH.

  48. REMOVE FRONT PILLAR GARNISH RH

    Tech Tips

    Use the same procedures described for the LH side.

  49. REMOVE ASSIST GRIP


    1. B007ONNE02
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, detach the 6 claws and open the 2 assist grip covers.

      Tech Tips

      Tape the screwdriver tip before use.

    2. B007U2Z

      Remove the 2 screws and assist grip.

  50. REMOVE VISOR ASSEMBLY LH


    1. B007V8M

      Remove the 2 screws and visor assembly LH.

  51. REMOVE VISOR ASSEMBLY RH

    Tech Tips

    Use the same procedures described for the LH side.

  52. REMOVE VISOR HOLDER

    Tech Tips

    Use the same procedures described for the other side.


    1. B007TEY

      Remove the screw.

    2. Using a moulding remover, detach the claw and remove the visor holder.

  53. REMOVE ROOM LIGHT ASSEMBLY NO. 1 (Deluxe)


    1. B007OKZE04
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, detach the 4 claws and remove the room light lens cover.

      Tech Tips

      Tape the screwdriver tip before use.

    2. B007TVK

      Remove the 2 screws and room light assembly No. 1.

    3. Disconnect the connector.

  54. REMOVE MAP LIGHT ASSEMBLY (Super Wagon)


    1. B007RWWE01

      Using a moulding remover, detach the 4 claws and map light assembly.

    2. Disconnect the connector.

  55. REMOVE REAR COOLER CONTROL PANEL


    1. B007WAQE01

      Release the 4 clips and 4 claws, and disconnect the rear cooler control panel.

    2. Disconnect the connector and remove the rear cooler control panel.

  56. REMOVE ROOF HEADLINING NO. 1 (for Middle Roof)


    1. B007P44E03

      Remove the 4 screws.

    2. Using a clip remover, remove the 8 clips.

    3. Using a clip remover, detach the clip A and remove the roof headlining No. 1.

  57. REMOVE ROOF HEADLINING NO. 1 (for High Roof)

    B007R9DE03

    1. Remove the 4 screws.

    2. Using a clip remover, remove the 14 clips.

    3. Using a clip remover, detach the clip A and remove the roof headlining No. 1.