CANISTER(w/o Canister Pump Module) REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during canister (charcoal canister assembly) removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Gas leak from exhaust system is repaired Inspection After Repair

  • Poor idle, etc.

  • Engine start function, etc.

Click here for Rear Air Fuel Ratio Sensor

Click here for Rear Heated Oxygen Sensor

PROCEDURE


  1. REMOVE TAIL EXHAUST PIPE ASSEMBLY

    CAUTION:

    To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.

    B007ZGP

    1. B007WV8

      Remove the 4 bolts and 2 compression springs and disconnect the tail exhaust pipe assembly from the center exhaust pipe assembly and No. 2 tail exhaust pipe assembly.

    2. Remove the tail exhaust pipe assembly from the 2 exhaust pipe supports.

    3. Remove the 2 exhaust pipe gaskets from the center exhaust pipe assembly and tail exhaust pipe assembly.

  2. REMOVE CHARCOAL CANISTER PROTECTOR

    B007XJE

    1. w/o Differential Pressure Sensor:


      1. Remove the 3 bolts and charcoal canister protector.

    2. B007XA9C01
      B007WXX Bolt
      B00803L Nut

      w/ Differential Pressure Sensor:


      1. Remove the 4 bolts, 3 nuts and charcoal canister protector.

  3. REMOVE CANISTER (CHARCOAL CANISTER ASSEMBLY) (w/o Differential Pressure Sensor)


    1. B007Z3DC03
      *a Retainer
      *b Claw
      B007WXX Pull
      B00803L Pull out
      B007X40 Pull off

      Disengage the 2 claws of the retainer. Pull out the retainer and disconnect the fuel tank vent hose sub-assembly from the canister (charcoal canister assembly).

      Note


      • Be sure to disconnect the fuel tank vent hose sub-assembly by hand.

      • Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the pipe.

      • Do not bend, twist, pinch or kink the fuel tank vent hose sub-assembly.

      • Protect the disconnected parts by covering them with plastic bags after disconnecting the fuel tank vent hose sub-assembly.

    2. Close the fuel tank vent hose sub-assembly using a hose plug or similar part.

    3. B007YOTC01
      *1 Charcoal Canister Hose
      *2 Outlet Charcoal Canister Tube Sub-assembly

      Slide the clip and disconnect the charcoal canister hose from the fuel tube.

    4. Slide the clip and disconnect the outlet charcoal canister tube sub-assembly from the canister (charcoal canister assembly).

    5. Disengage the clamp and disconnect the outlet charcoal canister tube sub-assembly.

    6. B007XWRC01
      *a Clip
      *b Guide

      Remove the 3 nuts and disengage the clip to remove the canister (charcoal canister assembly) from the vehicle body and guide.

  4. REMOVE CANISTER (CHARCOAL CANISTER ASSEMBLY) (w/ Differential Pressure Sensor)


    1. Pull out the retainer to disengage the lock claws and pull off the fuel tank vent hose sub-assembly from the canister (charcoal canister assembly).

      B007Z9DC01
      *a Retainer *b O-ring
      *c Tube Connector *d Pipe (Canister (Charcoal Canister Assembly))
      B007WXX Pull out B00803L Pull off

      Note


      • Be sure to disconnect the fuel tank vent hose sub-assembly by hand.

      • Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the pipe.

      • Do not bend, twist, pinch or kink the fuel tank vent hose sub-assembly.

      • Protect the disconnected parts by covering them with plastic bags after disconnecting the fuel tank vent hose sub-assembly.

    2. Close the fuel tank vent hose sub-assembly using a hose plug or similar part.

    3. B00803WC01
      *1 Charcoal Canister Hose
      *2 Outlet Charcoal Canister Tube Sub-assembly

      Slide the clip and disconnect the charcoal canister hose from the fuel tube.

    4. Slide the clip and disconnect the outlet charcoal canister tube sub-assembly from the canister (charcoal canister assembly).

    5. Disengage the clamp and disconnect the outlet charcoal canister tube sub-assembly.

    6. B007X35C01
      *a Clip
      *b Guide

      Remove the 3 nuts and disengage the clip to remove the canister (charcoal canister assembly) from the vehicle body and guide.