REAR SPEED SENSOR INSTALLATION

PROCEDURE


  1. INSTALL REAR SPEED SENSOR (for 2WD)


    1. for RH:

      A01L866

      1. Install the rear speed sensor RH with the bolt.

        Torque:
        8.5 N*m  { 87 kgf*cm, 75 in.*lbf }

        Note


        • Make sure there are no pieces of iron or other foreign matter attached to the sensor tip.

        • While inserting the speed sensor into the axle housing hole, do not strike or damage the sensor tip.

        • After installing the speed sensor, make sure there is no clearance or foreign matter between the sensor stay part and the axle housing.

      2. Install the harness clamp with the bolt.

        Torque:
        12.5 N*m  { 127 kgf*cm, 9 ft.*lbf }

        Note


        • When installing the clamp, do not twist the wire harness.

        • Make sure the clamp rotation stopper touches the installation position.

      3. Attach the 2 clamps.

        Note

        When attaching the clamps, do not twist the wire harness.

      4. Connect the connector and attach the clamp.

        Note


        • Securely attach the connector.

        • Securely connect the connector.

        • When connecting the connector, do not twist the wire harness.

    2. for LH:

      A01LB85N01

      1. Install the rear speed sensor LH with the bolt.

        Torque:
        8.5 N*m  { 87 kgf*cm, 75 in.*lbf }

        Note


        • Make sure there are no pieces of iron or other foreign matter attached to the sensor tip.

        • While inserting the speed sensor into the axle housing hole, do not strike or damage the sensor tip.

        • After installing the speed sensor, make sure there is no clearance or foreign matter between the sensor stay part and the axle housing.

      2. Install the 2 harness clamps with the 2 bolts.

        Torque:
        Bolt A
        12.5 N*m  { 127 kgf*cm, 9 ft.*lbf }
        Bolt B
        32 N*m  { 326 kgf*cm, 24 ft.*lbf }

        Note


        • When installing the clamps, do not twist the wire harness.

        • Make sure the clamp rotation stopper touches the installation position.

      3. Attach the clamp.

        Note

        When attaching the clamp, do not twist the wire harness.

      4. Connect the connector.

        Note


        • Securely connect the connector.

        • When connecting the connector, do not twist the wire harness.

  2. INSTALL REAR SPEED SENSOR (for 4WD and Pre-Runner)


    1. for RH:

      A01LF1L

      1. Install the rear speed sensor RH with the bolt.

        Torque:
        8.5 N*m  { 87 kgf*cm, 75 in.*lbf }

        Note


        • Make sure there are no pieces of iron or other foreign matter attached to the sensor tip.

        • While inserting the speed sensor into the axle housing hole, do not strike or damage the sensor tip.

        • After installing the speed sensor, make sure there is no clearance or foreign matter between the sensor stay part and the axle housing.

      2. Install the harness clamp with the bolt.

        Torque:
        12.5 N*m  { 127 kgf*cm, 9 ft.*lbf }

        Note


        • When installing the clamp, do not twist the wire harness.

        • Make sure the clamp rotation stopper touches the installation position.

      3. Attach the 2 clamps.

        Note

        When attaching the clamps, do not twist the wire harness.

      4. Connect the connector and attach the clamp.

        Note


        • Securely attach the connector.

        • Securely connect the connector.

        • When connecting the connector, do not twist the wire harness.

    2. for LH:

      A01LATEN01

      1. Install the rear speed sensor LH with the bolt.

        Torque:
        8.5 N*m  { 87 kgf*cm, 75 in.*lbf }

        Note


        • Make sure there are no pieces of iron or other foreign matter attached to the sensor tip.

        • While inserting the speed sensor into the axle housing hole, do not strike or damage the sensor tip.

        • After installing the speed sensor, make sure there is no clearance or foreign matter between the sensor stay part and the axle housing.

      2. Install the 2 harness clamps with the 2 bolts.

        Torque:
        Bolt A
        12.5 N*m  { 127 kgf*cm, 9 ft.*lbf }
        Bolt B
        32 N*m  { 326 kgf*cm, 24 ft.*lbf }

        Note


        • When installing the clamps, do not twist the wire harness.

        • Make sure the clamp rotation stopper touches the installation position.

      3. Attach the 2 clamps.

        Note

        When attaching the clamp, do not twist the wire harness.

      4. Connect the connector.

        Note


        • Securely connect the connector.

        • When connecting the connector, do not twist the wire harness.

  3. INSTALL REAR WHEEL

    Click here

  4. CHECK SPEED SENSOR SIGNAL


    1. w/ VSC:

      Click here

    2. w/o VSC:

      Click here