LOWER INSTRUMENT PANEL(for Hatchback, Wagon) INSTALLATION

PROCEDURE

  1. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY

    1. When using a new lower instrument panel sub-assembly:

      1. Immediately before installing the lower instrument panel sub-assembly, twist and cut off the portion shown in the illustration.

        B334382

    2. Install the lower instrument panel sub-assembly with the 2 bolts <A>, 8 screws <C> and screw <D>.

    3. for Automatic Air Conditioning System:

      1. Engage the 2 claws to connect the cooler (room temp. sensor) thermistor.

    4. Engage the 2 claws to connect the DLC3.

    5. Connect each connector.

    6. Engage each clamp.

  2. CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

    1. Engage the claw and 2 guides to connect the hood lock control lever sub-assembly.

  3. INSTALL GLOVE COMPARTMENT DOOR STOPPER SUB-ASSEMBLY

    1. Engage the claw to install the glove compartment door stopper sub-assembly.

  4. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY

    1. B334356C01

      *a

      Opened Approximately 53°

      *b

      Closed

      With the glove compartment door assembly opened approximately 53° from its closed position, engage the 2 hinges horizontally.

      Note:

      Engaging the hinges from the top will deform the hinges. Be sure to install the glove compartment door assembly horizontally.

    2. B334354C01

      *1

      Glove Compartment Door Stopper Sub-assembly

      *a

      Stopper

      Slightly bend the stoppers (A) and (B) in the directions indicated by the arrows in the illustration and engage the stoppers to install the glove compartment door assembly.

    3. Engage the claw to connect the glove compartment door stopper sub-assembly.

  5. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Instrument Panel Under Cover)

    1. Engage the guide and 3 claws to install the No. 2 instrument panel under cover sub-assembly.

  6. INSTALL COWL SIDE TRIM BOARD RH

    Tip:

    Use the same procedure as for the LH side.

    Click here

  7. INSTALL FRONT DOOR SCUFF PLATE RH

    Tip:

    Use the same procedure as for the LH side.

    Click here

  8. INSTALL CENTER INSTRUMENT PANEL SAFETY PAD RETAINER WITH AIR CONDITIONING CONTROL ASSEMBLY

    Click hereClick here

  9. INSTALL NO. 1 NAVIGATION ANTENNA CORD SUB-ASSEMBLY (w/ Navigation System)

    Click here

  10. INSTALL STEREO OPENING COVER WITH BRACKET (w/o Radio Receiver)

    1. Connect the connector.

    2. Engage the 2 guides.

    3. Install the stereo opening cover with bracket with the 4 bolts <B>.

  11. INSTALL RADIO RECEIVER ASSEMBLY WITH BRACKET (w/ Radio Receiver)

    Click here

  12. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (w/o Knee Airbag)

    1. Engage the 7 clips to install the lower instrument panel finish panel sub-assembly.

  13. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Knee Airbag)

    Click here

  14. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Instrument Panel Under Cover)

    1. Engage the guide and claw.

    2. Install the No. 1 instrument panel under cover sub-assembly with the 2 screws <E>.

  15. INSTALL NO. 1 SWITCH HOLE BASE (for LHD)

    1. w/o Entry and Start System:

      1. B334304

        Engage the 4 clips to install the No. 1 switch hole base as shown in the illustration.

    2. w/ Entry and Start System:

      1. Connect the connector.

      2. B334302

        Engage the 4 clips to install the No. 1 switch hole base as shown in the illustration.

  16. INSTALL NO. 1 SWITCH HOLE BASE (for RHD)

    1. Connect the connector.

    2. B328172

      Engage the 4 clips to install the No. 1 switch hole base as shown in the illustration.

  17. INSTALL NO. 2 SWITCH HOLE BASE (for LHD)

    1. B334300

      Engage the 3 clips to install the No. 2 switch hole base as shown in the illustration.

  18. INSTALL NO. 2 SWITCH HOLE BASE (for RHD)

    1. w/o Entry and Start System:

      1. B328170

        Engage the 5 clips to install the No. 2 switch hole base as shown in the illustration.

    2. w/ Entry and Start System:

      1. Connect the connector.

      2. B328167

        Engage the 4 clips to install the No. 2 switch hole base as shown in the illustration.

  19. INSTALL LOWER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (for LHD)

    1. Connect each connector.

    2. Engage the 8 clips to install the lower instrument cluster finish panel assembly.

  20. INSTALL LOWER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (for RHD)

    1. w/o Entry and Start System:

      1. Connect each connector.

      2. Engage the claw and 6 clips to install the lower instrument cluster finish panel assembly.

    2. w/ Entry and Start System:

      1. Connect each connector.

      2. Engage the 8 clips to install the lower instrument cluster finish panel assembly.

  21. INSTALL COWL SIDE TRIM BOARD LH

    Click here

  22. INSTALL FRONT DOOR SCUFF PLATE LH

    Click here

  23. INSTALL CONSOLE BOX ASSEMBLY

    Click here

  24. INSTALL UPPER INSTRUMENT PANEL ASSEMBLY

    Click here