PRE-CRASH SAFETY SYSTEM, Diagnostic DTC:C1A0A

DTC Code DTC Name
C1A0A Front Radar Sensor Region Code Mismatch

DESCRIPTION

The driving support ECU assembly uses the millimeter wave radar sensor assembly to detect obstacles in front of the vehicle.

Based on signals from the millimeter wave radar sensor assembly, the driving support ECU assembly calculated the risk of a collision and operates the pre-crash when it determines that the risk is high.

When the millimeter wave radar sensor assembly is replaced with a new one, it acquires the country specification information from the driving support ECU assembly. Also, when the driving support ECU assembly is replaced with a new one, it receives country specification information from the main body ECU (multiplex network body ECU). When country specification information in the millimeter wave radar sensor assembly, driving support ECU and/or main body ECU do not match, DTC C1A0A is stored.

The driving support ECU assembly uses the millimeter wave radar sensor assembly to detect obstacles in front of the vehicle.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

C1A0A

Front Radar Sensor Region Code Mismatch

While the power switch is on (IG), the country specification information from the driving support ECU assembly and millimeter wave radar sensor assembly do not match for approximately 2 seconds.

  • Millimeter wave radar sensor assembly

  • Driving support ECU assembly

CAUTION / NOTICE / HINT

Note:

  • First check the CAN communication system by following How to Proceed with Troubleshooting. After checking that there are no malfunctions in the CAN communication system, proceed with troubleshooting.

    Click here

  • When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.

    Click here

  • When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.

  • If a millimeter wave radar sensor assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly and millimeter wave radar sensor assembly will not match and a DTC may be stored.

PROCEDURE

  1. CHECK FOR DTC

    1. Clear the DTCs.

      Click here

      Body Electrical > Pre-Crash 2 > Clear DTCs

    2. Make sure that the DTC detection conditions are met.

      Tip:

      If the detection conditions are not met, the system cannot detect the malfunction.

    3. Check for DTCs.

      Click here

      Body Electrical > Pre-Crash 2 > Trouble Codes

      OK

      DTC C1A0A is not output.

    Result

    Proceed to

    OK

    NG
    OK

    USE SIMULATION METHOD TO CHECK

    Click hereClick hereClick here

    NG

  2. REPLACE DRIVING SUPPORT ECU ASSEMBLY

    1. Replace the driving support ECU assembly with a new one.

      for LHD:Click here

      for RHD:Click here

    Result

    Proceed to

    NEXT
    NEXT

  3. CHECK FOR DTC

    1. Clear the DTCs.

      Click here

      Body Electrical > Pre-Crash 2 > Clear DTCs

    2. Make sure that the DTC detection conditions are met.

      Tip:

      If the detection conditions are not met, the system cannot detect the malfunction.

    3. Check for DTCs.

      Click here

      Body Electrical > Pre-Crash 2 > Trouble Codes

      OK

      DTC C1A0A is not output.

    Result

    Proceed to

    OK

    NG
    OK

    END (DRIVING SUPPORT ECU ASSEMBLY WAS DEFECTIVE)

    NG

  4. REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

    1. Replace the millimeter wave radar sensor assembly with a new one.

      Click here

    2. Adjust the millimeter wave radar sensor assembly.

      Click here

    Result

    Proceed to

    NEXT
    NEXT

    END (MILLIMETER WAVE RADAR SENSOR ASSEMBLY WAS DEFECTIVE)