ROOF HEADLINING REMOVAL

PROCEDURE

  1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note:

    • After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).

    • When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  2. REMOVE REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat)

    1. Remove the rear No. 2 seat assembly (Click here).

  3. REMOVE REAR NO. 1 SEAT ASSEMBLY

    1. for 60/40 Split Slide Walk-in Seat Type LH Side:

      Remove the rear No. 1 seat assembly (Click here).

    2. for 60/40 Split Slide Walk-in Seat Type RH Side:

      Remove the rear No. 1 seat assembly (Click here).

  4. REMOVE REAR NO. 1 SEATBACK ASSEMBLY

    1. for 60/40 Split Double-folding Seat Type LH Side:

      Remove the rear No. 1 seatback assembly (Click here).

    2. for 60/40 Split Double-folding Seat Type RH Side:

      Remove the rear No. 1 seatback assembly (Click here).

  5. REMOVE DOOR SCUFF PLATE ASSEMBLY LH

    B238732C02

    *1

    Protective Tape

    1. Put protective tape around the door scuff plate.

    2. Using a screwdriver, detach the 4 clips, 10 claws and 2 guides.

      Tip:

      Tape the screwdriver tip before use.

    3. Disconnect the connector and remove the door scuff plate.

  6. REMOVE DOOR SCUFF PLATE ASSEMBLY RH

    Tip:

    Use the same procedure described for the LH side.

  7. REMOVE COWL SIDE TRIM BOARD LH

    B238734

    1. Remove the clip.

    2. Detach the clip and claw and remove the cowl side trim board.

  8. REMOVE COWL SIDE TRIM BOARD RH

    Tip:

    Use the same procedure described for the LH side.

  9. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

    B238778

    1. Remove the front door opening trim weatherstrip.

  10. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

    Tip:

    Use the same procedure described for the LH side.

  11. REMOVE FRONT NO. 1 ASSIST GRIP PLUG LH

    B238741C01

    *1

    Protective Tape
    Tip:

    Use the same procedure for the other front No. 1 assist grip plug.

    1. Using a screwdriver, detach the 2 claws and remove the front No. 1 assist grip plug.

      Tip:

      Tape the screwdriver tip before use.

  12. REMOVE FRONT NO. 1 ASSIST GRIP PLUG RH

    Tip:

    Use the same procedure described for the LH side.

  13. REMOVE NO. 1 ASSIST GRIP

    B238742
    Tip:

    Use the same procedure for the other No. 1 assist grip.

    1. Remove the 2 bolts.

    2. Detach the 2 claws and remove the No. 1 assist grip.

  14. REMOVE FRONT PILLAR GARNISH LH

    B238743

    1. Detach the 3 guides and remove the front pillar garnish.

    2. B238744C01

      *1

      Curtain Shield Airbag Assembly

      *2

      Adhesive Tape

      *3

      Protective Cover

      Protect the curtain shield airbag assembly.

      1. Completely cover the airbag with a cloth or nylon sheet and secure the ends of the cover with adhesive tape as shown in the illustration.

        Note:

        Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.

  15. REMOVE FRONT PILLAR GARNISH RH

    Tip:

    Use the same procedure described for the LH side.

  16. REMOVE REAR NO. 1 FLOOR STEP COVER (w/ Rear No. 2 Seat)

    B238730C01

    *1

    Protective Tape
    Tip:

    Use the same procedure for all rear No. 1 floor step covers.

    1. Using a screwdriver, detach the 2 claws and remove the rear No. 1 floor step cover.

      Tip:

      Tape the screwdriver tip before use.

  17. REMOVE QUARTER SCUFF PLATE LH (w/ Rear No. 2 Seat)

    B238731

    1. Remove the 2 bolts and quarter scuff plate.

  18. REMOVE QUARTER SCUFF PLATE RH (w/ Rear No. 2 Seat)

    Tip:

    Use the same procedure described for the LH side.

  19. REMOVE REAR DOOR SCUFF PLATE LH

    B238733C01

    *1

    Protective Tape

    1. Put protective tape around the rear door scuff plate.

    2. Using a screwdriver, detach the 3 clips, 6 claws and 2 guides and remove the rear door scuff plate.

      Tip:

      Tape the screwdriver tip before use.

  20. REMOVE REAR DOOR SCUFF PLATE RH

    Tip:

    Use the same procedure described for the LH side.

  21. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

    B238780

    1. Remove the rear door opening trim weatherstrip.

  22. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

    Tip:

    Use the same procedure described for the LH side.

  23. REMOVE OUTER LAP BELT ANCHOR COVER

    B238735
    Tip:

    Use the same procedure for the other outer lap belt anchor cover.

    1. Detach the 3 claws and remove the outer lap belt anchor cover.

  24. REMOVE LOWER CENTER PILLAR GARNISH LH

    B238736

    1. Remove the bolt and disconnect the front seat outer belt floor anchor.

    2. B238737

      Detach the 4 claws and 2 clips and remove the lower center pillar garnish.

  25. REMOVE LOWER CENTER PILLAR GARNISH RH

    Tip:

    Use the same procedure described for the LH side.

  26. REMOVE NO. 2 ASSIST GRIP PLUG LH

    B238739C01

    *1

    Protective Tape
    Tip:

    Use the same procedure for the other front No. 2 assist grip plug.

    1. Using a screwdriver, detach the 2 claws and remove the front No. 2 assist grip plug.

      Tip:

      Tape the screwdriver tip before use.

  27. REMOVE NO. 2 ASSIST GRIP PLUG RH

    Tip:

    Use the same procedure described for the LH side.

  28. REMOVE NO. 2 ASSIST GRIP

    B238740
    Tip:

    Use the same procedure for the other No. 2 assist grip.

    1. Remove the 2 bolts.

    2. Detach the 2 claws and remove the No. 2 assist grip.

  29. REMOVE CENTER PILLAR GARNISH LH

    B238738

    1. Move the front shoulder belt anchor adjuster to the lowest position.

    2. Remove the bolt.

    3. Detach the 2 clips and 2 guides.

    4. Pass the front seat outer belt floor anchor through the center pillar garnish and remove the center pillar garnish.

  30. REMOVE CENTER PILLAR GARNISH RH

    Tip:

    Use the same procedure described for the LH side.

  31. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)

    1. Remove the tonneau cover.

  32. REMOVE FRONT LUGGAGE COMPARTMENT TRIM COVER (w/o Rear No. 2 Seat)

    B240044
    Tip:

    Use the same procedure for the other front luggage compartment trim cover.

    1. Detach the 4 claws and remove the cap.

    2. B238749C01

      *1

      Luggage Hold Belt Striker

      Remove the bolt, luggage hold belt striker and front luggage compartment trim cover.

  33. REMOVE NO. 1 DECK BOARD SUB-ASSEMBLY (w/o Rear No. 2 Seat)

    B238750

    1. Detach the clip and remove the No. 1 deck board.

  34. REMOVE REAR FLOOR MAT REAR SUPPORT PLATE (w/o Rear No. 2 Seat)

    B238748

    1. Detach the 5 clips and 4 claws and remove the rear floor mat rear support plate.

  35. REMOVE REAR FLOOR CARPET ASSEMBLY (w/o Rear No. 2 Seat)

    B247868

    1. Detach the 4 claws and remove the rear floor carpet.

  36. REMOVE REAR NO. 1 SEAT OUTER LAP BELT ANCHOR COVER

    B238752
    Tip:

    Use the same procedure for the other rear No. 1 seat outer lap belt anchor cover.

    1. Detach the 3 claws and remove the rear No. 1 seat outer lap belt anchor cover.

  37. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

    B181695
    Tip:

    Use the same procedure for the other No. 1 luggage compartment trim hook.

    1. Remove the luggage compartment trim hook by turning it clockwise.

  38. REMOVE NO. 1 TONNEAU COVER HOLDER CAP (w/o Tonneau Cover)

    B238754C01

    *1

    Protective Tape
    Tip:

    Use the same procedure for the other No. 1 tonneau cover holder cap.

    1. Using a screwdriver, detach the 2 claws and remove the No. 1 tonneau cover holder cap.

      Tip:

      Tape the screwdriver tip before use.

  39. REMOVE FRONT DECK SIDE TRIM COVER (w/ Tonneau Cover)

    B240051C01

    *1

    Protective Tape
    Tip:

    Use the same procedure for the other front deck side trim cover.

    1. Using a screwdriver, detach the 2 claws and remove the front deck side trim cover.

      Tip:

      Tape the screwdriver tip before use.

  40. REMOVE ASSIST GRIP PLUG (w/ Rear No. 2 Seat)

    B238757C01

    *1

    Protective Tape
    Tip:

    Use the same procedure for all assist grip plugs.

    1. Using a screwdriver, detach the 2 claws and remove the assist grip plug.

      Tip:

      Tape the screwdriver tip before use.

  41. REMOVE ASSIST GRIP SUB-ASSEMBLY (w/ Rear No. 2 Seat)

    B238758
    Tip:

    Use the same procedure for the other assist grip.

    1. Remove the 2 bolts and assist grip.

  42. REMOVE REAR SEATBACK LOCK CONTROL LEVER BASE LH (w/o Rear No. 2 Seat)

    Click here

  43. REMOVE REAR SEATBACK LOCK CONTROL LEVER BASE RH (w/o Rear No. 2 Seat)

    Click here

  44. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH

    1. w/o Rear No. 2 Seat:

      1. B238753

        Remove the bolt and disconnect the rear No. 1 seat outer belt floor anchor.

      2. Remove the 4 bolts and 2 screws.

      3. Detach the 5 clips and 8 claws and remove the deck trim side panel.

        B238755

    2. w/ Rear No. 2 Seat:

      1. B238753

        Remove the bolt and disconnect the rear No. 1 seat outer belt floor anchor.

      2. B238759

        Remove the bolt and disconnect the rear No. 2 seat outer belt floor anchor.

      3. Remove the 2 bolts and 2 screws.

      4. Detach the 3 clips and 8 claws.

      5. Disconnect each connector and remove the deck trim side panel.

        B247869

  45. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH

    1. w/o Rear No. 2 Seat:

      1. B238821

        Remove the bolt and disconnect the rear No. 1 seat outer belt floor anchor.

      2. Remove the 4 bolts and screw.

      3. Detach the 5 clips and 8 claws.

      4. Disconnect each connector and remove the deck trim side panel.

        B238822

    2. w/ Rear No. 2 Seat:

      1. B238821

        Remove the bolt and disconnect the rear No. 1 seat outer belt floor anchor.

      2. B238826

        Remove the bolt and disconnect the rear No. 2 seat outer belt floor anchor.

      3. Remove the 2 bolts and screw.

      4. Detach the 3 clips and 8 claws.

      5. Disconnect each connector and remove the deck trim side panel.

        B247870

    3. w/ Rear Air Duct:

      1. B238821

        Remove the bolt and disconnect the rear No. 1 seat outer belt floor anchor.

      2. B238826

        Remove the bolt and disconnect the rear No. 2 seat outer belt floor anchor.

      3. Remove the 2 bolts and screw.

      4. Detach the 3 clips and 8 claws.

      5. Disconnect each connector and remove the deck trim side panel.

        B324020

  46. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY LH

    B238745

    1. Move the rear shoulder belt anchor adjuster to the lowest position.

    2. Detach the 2 clips and 2 guides.

    3. Pass the rear No. 1 seat outer belt floor anchor through the front quarter trim panel and remove the front quarter trim panel.

  47. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY RH

    Tip:

    Use the same procedure described for the LH side.

  48. REMOVE REAR QUARTER TRIM PANEL ASSEMBLY LH

    B238746

    1. w/o Rear No. 2 Seat:

      1. Detach the 7 clips and 2 guides and remove the rear quarter trim panel.

    2. B247871

      w/ Rear No. 2 Seat:

      1. Detach the 7 clips and 2 guides.

      2. Disconnect the connector.

      3. B238747

        Detach the 4 claws and 2 guides, pass the rear No. 2 seat outer belt floor anchor through the rear quarter trim panel and remove the rear quarter trim panel.

  49. REMOVE REAR QUARTER TRIM PANEL ASSEMBLY RH

    Tip:

    Use the same procedure described for the LH side.

  50. REMOVE ASSIST GRIP SUB-ASSEMBLY

    B184001C01

    *1

    Protective Tape
    Tip:

    Use the same procedure for the other assist grip.

    1. Using a screwdriver, detach the 4 claws and remove the 2 assist grip covers.

      Tip:

      Tape the screwdriver tip before use.

    2. Detach the 2 clips and remove the assist grip.

    3. Remove the 2 clips from the vehicle body.

  51. REMOVE REAR ASSIST GRIP ASSEMBLY LH

    B184002C01

    *1

    Protective Tape

    1. Using a screwdriver, detach the 4 claws and remove the 2 assist grip covers.

      Tip:

      Tape the screwdriver tip before use.

    2. Detach the 2 clips and remove the assist grip.

    3. Remove the 2 clips from the vehicle body.

  52. REMOVE REAR ASSIST GRIP ASSEMBLY RH

    Tip:

    Use the same procedure described for the LH side.

  53. REMOVE ASSIST GRIP

    B238761C01

    *1

    Protective Tape
    Tip:

    Use the same procedure for the other assist grip.

    1. Using a screwdriver, detach the 4 claws and open the 2 covers.

      Tip:

      Tape the screwdriver tip before use.

    2. B238762

      Remove the 2 bolts and assist grip.

  54. REMOVE VISOR BRACKET COVER

    B181706
    Tip:

    Use the same procedure for the other visor bracket cover.

    1. Detach the 4 claws and remove the visor bracket cover.

  55. REMOVE VISOR ASSEMBLY LH

    B181707

    1. Remove the 2 screws and visor.

  56. REMOVE VISOR ASSEMBLY RH

    Tip:

    Use the same procedure described for the LH side.

  57. REMOVE VISOR HOLDER

    B151362E02
    Tip:

    Use the same procedure for the other visor holder.

    1. Turn the visor holder approximately 45° and pull it out as shown in the illustration.

    2. Detach the 2 claws and remove the visor holder.

  58. REMOVE MAP LIGHT ASSEMBLY

    Click here

  59. REMOVE RAIN SENSOR COVER

    Click here

  60. REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER

    Click here

  61. REMOVE NO. 1 ROOM LIGHT ASSEMBLY

    1. for Center:

      Remove the No. 1 room light assembly (Click here).

    2. for Rear:

      Remove the No. 1 room light assembly (Click here).

  62. REMOVE REAR SIDE NO. 1 AIR DUCT (w/ Rear Air Conditioning System)

    Click here

  63. REMOVE ROOF HEADLINING ASSEMBLY

    1. Disconnect the inner mirror connector.

    2. E197773

      Disconnect the rain sensor connector.

    3. B238774

      Disconnect the drive gear connector.

    4. B238771

      Disconnect the 2 connectors and detach the 3 clamps from the front pillar LH.

    5. B238770

      Remove the bolt.

    6. Disconnect the 2 connectors and detach the 3 clamps from the front pillar RH.

    7. B238773

      Disconnect the 2 connectors and detach the clamp from the rear pillar LH.

    8. B238772

      Disconnect the connector and detach the 3 clamps from the rear pillar RH.

    9. B247872C01

      *1

      Guide

      *2

      Fastener

      Detach the 2 clips, 2 guides and 8 fasteners.

    10. B247491

      Disconnect the antenna cord connector.

    11. B247492

      Remove the roof headlining from the back door as shown in the illustration.

      Note:

      Be careful not to damage the roof headlining when removing it.

  64. REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH

    B238795

    1. Detach the 5 claws of the front shoulder belt anchor plate and slide the front shoulder belt anchor plate to remove it.

  65. REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH

    Tip:

    Use the same procedure described for the LH side.

  66. REMOVE REAR SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH

    B238794

    1. Detach the 6 claws of the rear shoulder belt anchor plate and slide the rear shoulder belt anchor plate to remove it.

  67. REMOVE REAR SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH

    Tip:

    Use the same procedure described for the LH side.

  68. REMOVE NO. 1 ROOF SIDE RAIL GARNISH LH

    B238768C01

    *a

    Cut Off Position

    1. Detach the 3 clips.

    2. Cut off the 3 clips and remove the roof side rail garnish.

    3. Remove the 3 clips from the vehicle body.

  69. REMOVE NO. 1 ROOF SIDE RAIL GARNISH RH

    Tip:

    Use the same procedure described for the LH side.

  70. REMOVE ROOF SIDE INNER GARNISH CAP LH (w/o Rear No. 2 Seat)

    B238799

    1. Detach the 4 claws and 2 guides and remove the roof side inner garnish cap.

  71. REMOVE ROOF SIDE INNER GARNISH CAP RH (w/o Rear No. 2 Seat)

    Tip:

    Use the same procedure described for the LH side.

  72. REMOVE REAR SEAT SHOULDER BELT HANGER LH

    B238782

    1. Detach the claw and guide and remove the rear seat shoulder belt hanger.

  73. REMOVE REAR SEAT SHOULDER BELT HANGER RH

    Tip:

    Use the same procedure described for the LH side.

  74. REMOVE QUARTER TRIM COVER

    B238798
    Tip:

    Use the same procedure for the other quarter trim cover.

    1. Detach the 2 claws and remove the quarter trim cover.

  75. REMOVE QUARTER TRIM JACK COVER

    B238797

    1. Detach the 3 claws and 2 guides and remove the quarter trim jack cover.

  76. REMOVE DECK SIDE TRIM COVER LH

    B238796

    1. Detach the 3 claws and 2 guides and remove the deck side trim cover.