FIT STANDARD / ADJUSTMENT METHOD ADJUSTMENT


  1. INSPECT HOOD SUB-ASSEMBLY


    1. Check that the clearance measurements of areas A to E are within the standard ranges.

      A01GH5AN03

    2. ADJUST HOOD SUB-ASSEMBLY


      1. A01GHEC

        Adjust the hood position.


        1. Loosen the 4 hinge bolts on the hood and adjust the hood position.

        2. Move the hood and adjust the clearance between the hood and front fender.

        3. Tighten the 4 hinge bolts on the hood after the adjustment.

          Torque:
          13 N*m  { 133 kgf*cm, 9.6 ft.*lbf }
      2. A01GHCX

        Adjust the cushion rubber so that the hood and fender are aligned.

        Tech Tips

        Raise or lower the front end of the hood by turning the cushion rubber.

      3. A01GH63

        Adjust the hood lock.


        1. Loosen the 3 bolts.

        2. Adjust the hood lock position so that the striker can enter it smoothly.

        3. Tighten the 3 bolts after the adjustment.

          Torque:
          8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

    3. INSPECT FRONT DOOR PANEL SUB-ASSEMBLY


      1. Check that the clearance measurements of areas A to H are within the standard ranges.

        A01GH5DC01

    4. ADJUST FRONT DOOR PANEL SUB-ASSEMBLY


      1. A01GH5H

        Using SST, loosen the hinge bolts on the body and adjust the door position.

        SST
        09812-00010

      2. Tighten the hinge bolts on the body after the adjustment.

        Torque:
        26 N*m  { 265 kgf*cm, 19 ft.*lbf }
      3. A01GH5F

        Loosen the hinge bolts on the door and adjust the door position.

      4. Tighten the hinge bolts on the door after the adjustment.

        Torque:
        26 N*m  { 265 kgf*cm, 19 ft.*lbf }
      5. A01GHFJ

        Detach the 4 claws and remove the striker cover.

      6. A01GHH4

        Using a T40 "TORX" socket wrench, adjust the striker position by slightly loosening the striker mounting screws and hitting the striker with a plastic-faced hammer.

        Torque:
        23 N*m  { 235 kgf*cm, 17 ft.*lbf }

      7. Attach the 4 claws and install the striker cover.

    5. INSPECT REAR DOOR PANEL SUB-ASSEMBLY


      1. Check that the clearance measurements of areas A to H are within the standard ranges.

        A01GH7TN01

    6. ADJUST REAR DOOR PANEL SUB-ASSEMBLY


      1. A01GHB2

        Using SST, loosen the hinge bolts on the body and adjust the door position.

        SST
        09812-00010

      2. Tighten the hinge bolts on the body after the adjustment.

        Torque:
        26 N*m  { 265 kgf*cm, 19 ft.*lbf }
      3. A01GH9P

        Loosen the hinge bolts on the door and adjust the door position.

      4. Tighten the hinge bolts on the door after the adjustment.

        Torque:
        26 N*m  { 265 kgf*cm, 19 ft.*lbf }
      5. A01GHBQ

        Detach the 4 claws and remove the striker cover.

      6. A01GHDO

        Using a T40 "TORX" socket wrench, adjust the striker position by slightly loosening the striker mounting screws and hitting the striker with a plastic-faced hammer.

        Torque:
        23 N*m  { 235 kgf*cm, 17 ft.*lbf }

      7. Attach the 4 claws and install the striker cover.

    7. REMOVE BACK DOOR PANEL SUB-ASSEMBLY


      1. Check that the clearance measurements of areas A to I are within the standard ranges.

        A01GHGVN04

    8. ADJUST BACK DOOR PANEL SUB-ASSEMBLY


      1. A01GHE5

        Before adjusting the upper end of the back door up and down or left and right, loosen the bolts.

      2. Tighten the hinge bolts on the body after the adjustment.

        Torque:
        15.5 N*m  { 158 kgf*cm, 11 ft.*lbf }
      3. A01GHGB

        Using a T40 "TORX" socket wrench, adjust the striker position by slightly loosening the striker mounting screws and hitting the striker with a plastic-faced hammer.

      4. Using a T40 "TORX" socket wrench, tighten the striker mounting screws after the adjustment.

        Torque:
        23 N*m  { 235 kgf*cm, 17 ft.*lbf }