METER / GAUGE SYSTEM ON-VEHICLE INSPECTION

PROCEDURE

  1. INSPECT COMBINATION METER ASSEMBLY

    1. Check speedometer operation

      Note:

      • The combination meter assembly receives the vehicle speed signal from the skid control ECU via CAN communication. Therefore, perform the following inspection referring to values on the Data List of the skid control ECU because it is the source of the vehicle speed signal.

      • The Data List values of the skid control ECU are used for this inspection. Therefore, make sure to perform this inspection after confirming that no DTCs are output from the brake control system.

      • If the tire size or tire inflation pressure is not within the specified range, or the tires are excessively worn, the speedometer indication error will increase. Therefore, make sure to perform this inspection after checking that the tire size, tire inflation pressure and tire wear are in the specified range.

      1. Before starting the following inspection, check if brake control system DTCs are output.

      2. Check the values by referring to the table below.

        Chassis > ABS/VSC/TRC > Data List

        Tester Display

        Measurement Item

        Normal Condition

        Diagnostic Note

        Vehicle Speed

        Maximum wheel speed sensor reading/Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)

        Vehicle stopped: 0 km/h (0 mph)

        When driving at constant speed: No large fluctuations

        Chassis > ABS/VSC/TRC > Data List

        Tester Display

        Vehicle Speed
        Table 1. Reference km/h

        GTS Indication (km/h)

        Acceptable Range (km/h)

        20

        21.2 to 25.2

        40

        42.2 to 46.7

        60

        63.5 to 68.0

        80

        84.6 to 89.6

        100

        105.8 to 110.8

        120

        126.9 to 132.4

        140

        147.9 to 153.9

        160

        168.6 to 175.6

        180

        189.6 to 197.2

        200

        210.8 to 218.8

        220

        231.8 to 240.2
        Table 2. Reference mph

        GTS Indication (mph)

        Acceptable Range (mph)

        20

        21.2 to 23.7

        40

        42.6 to 45.1

        60

        63.4 to 66.9

        80

        84.3 to 88.3

        100

        105.4 to 109.9

        120

        126.5 to 131.4

        140

        147.6 to 152.9

        160

        168.7 to 174.4

    2. Inspect tachometer

      1. Connect the GTS and start the engine.

      2. Compare the test results with the tachometer indication.

        Table 3. DC 13.5 V, at 25°C (77°F)

        GTS Indication (rpm)

        Acceptable Range (rpm)

        Data in ( ) is for Reference

        700

        630 to 770

        1000

        (900 to 1100)

        2000

        (1850 to 2150)

        3000

        2800 to 3200

        4000

        (3800 to 4200)

        5000

        4800 to 5200

        6000*

        (5750 to 6250)

        7000*

        6700 to 7300

        • *: for Gasoline

    3. Check LED illumination (LED check)

      1. Check the illumination function of the warning or indicator lights listed below when turning the ignition switch to ON.

        OK

        Warning or Indicator Light

        Specified Condition

        Eco driving indicator*1, *10, *11

        Warning or indicator light comes on for about 3 seconds after turning the ignition switch to ON.

        Oil maintenance warning*2, *10

        Fuel sedimenter warning*2, *10

        Stop and start indicator*3, *10

        Stop and start off warning*3

        AFS OFF warning*4

        Brake warning

        TRC OFF warning*5

        VSC OFF warning*5

        Slip warning*5

        ABS warning

        Engine oil level warning*2, *10

        DPF warning*2, *10

        Automatic high beam indicator*6

        Engine coolant temperature hot warning*10

        Master warning*7

        Speed warning*10, *12

        Washer fluid level warning*10, *13

        Tire pressure warning*7, *14

        Multi-mode manual transaxle warning*8

        Warning light comes on for about 5 seconds after turning the ignition switch to ON.

        SRS warning

        Warning light comes on for about 6 seconds after turning the ignition switch to ON.

        Shift up or down indicator*9, *10

        Warning or indicator light comes on when turning the ignition switch to ON.

        Charge warning*10

        Engine oil pressure warning*10

        MIL (Check engine warning light)

        EPS warning

        • *1: for CVT

        • *2: for Diesel

        • *3: w/ Stop and start system

        • *4: w/ AFS (Adaptive Front-lighting System)

        • *5: w/ VSC

        • *6: w/ Automatic high beam system

        • *7: for Multi-information display (Dot LCD type)

        • *8: for Multi-mode manual transaxle

        • *9: for Manual transaxle or multi-mode manual transaxle

        • *10: for Multi-information display (Segment LCD type)

        • *11: Turns on only when the ECO customize setting is set to On.

        • *12: w/ Speed warning

        • *13: w/ Washer fluid level warning

        • *14: w/ Tire pressure warning system