LIN COMMUNICATION SYSTEM, Diagnostic DTC:B2322

DTC Code DTC Name
B2322 Front Passenger Side Door ECU Communication Stop

DESCRIPTION

This DTC is stored when LIN communication between the front door window regulator assembly (for front passenger door) and main body ECU (multiplex network body ECU) stops for 10 seconds or more.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

B2322

Front Passenger Side Door ECU Communication Stop

No communication between front door window regulator assembly (for front passenger door) and main body ECU (multiplex network body ECU) for 10 seconds or more.

  • Front door window regulator assembly (for front passenger door)

  • Main body ECU (multiplex network body ECU)

  • Instrument panel junction block assembly

  • Wire harness or connector

  • DOOR NO. 2 fuse

WIRING DIAGRAM

  1. for LHD

    B296571E18

  2. for RHD

    B296571E19

CAUTION / NOTICE / HINT

Note:

  • Inspect the fuses for circuits related to this system before performing the following procedure.

  • When a front door window regulator assembly is replaced or removed and reinstalled, it requires initialization.

    for Models with Jam Protection Function on 4 Windows:Click here

    for Models with Jam Protection Function on Driver Door Window Only:Click here

PROCEDURE

  1. INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

    1. Remove the instrument panel junction block assembly.

      for LHD:Click hereClick here

      for RHD:Click hereClick here

      B330524C03

      *a

      Component without harness connected

      (Instrument Panel Junction Block Assembly)

      -

      -

    2. Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

    3. Measure the resistance according to the value(s) in the table below.

      Tip:

      This inspection is to check the LIN communication line in the instrument panel junction block assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      3C-22 - MB-16 (LIN2)

      Always

      Below 1 Ω

    Result

    Proceed to

    OK

    NG
    NG

    REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

    for LHD:Click hereClick here

    for RHD:Click hereClick here

    OK

  2. CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - FRONT DOOR WINDOW REGULATOR ASSEMBLY (for Front Passenger Door))

    1. for LHD

      1. Disconnect the G13 front door window regulator assembly (for front passenger door) connector.

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance

        Tester Connection

        Condition

        Specified Condition

        3C-22 - G13-9 (LIN)

        Always

        Below 1 Ω

        G13-9 (LIN) - Body ground

        Always

        10 kΩ or higher

        3C-22 - Body ground

        Always

        10 kΩ or higher

    2. for RHD

      1. Disconnect the H4 front door window regulator assembly (for front passenger door) connector.

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance

        Tester Connection

        Condition

        Specified Condition

        3C-22 - H4-9 (LIN)

        Always

        Below 1 Ω

        H4-9 (LIN) - Body ground

        Always

        10 kΩ or higher

        3C-22 - Body ground

        Always

        10 kΩ or higher

    Result

    Proceed to

    OK

    NG
    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. CHECK HARNESS AND CONNECTOR (FRONT DOOR WINDOW REGULATOR ASSEMBLY (for Front Passenger Door) - BATTERY, BODY GROUND)

    1. for LHD

      1. Measure the voltage according to the value(s) in the table below.

        Standard Voltage

        Tester Connection

        Condition

        Specified Condition

        G13-2 (B) - G13-1 (GND)

        Always

        11 to 14 V

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance

        Tester Connection

        Condition

        Specified Condition

        G13-1 (GND) - Body ground

        Always

        Below 1 Ω

    2. for RHD

      1. Measure the voltage according to the value(s) in the table below.

        Standard Voltage

        Tester Connection

        Condition

        Specified Condition

        H4-2 (B) - H4-1 (GND)

        Always

        11 to 14 V

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance

        Tester Connection

        Condition

        Specified Condition

        H4-1 (GND) - Body ground

        Always

        Below 1 Ω

    Result

    Proceed to

    OK

    NG
    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. REPLACE FRONT DOOR WINDOW REGULATOR ASSEMBLY (for Front Passenger Door)

    1. Replace the front door window regulator assembly (for front passenger door).

      Click here

    Result

    Proceed to

    NEXT
    NEXT

  5. CHECK DTC OUTPUT

    1. Clear the DTCs.

      Click here

      Body Electrical > Main Body > Clear DTCs

    2. Recheck for DTCs.

      Body Electrical > Main Body > Trouble Codes

      OK

      DTC B2322 is not output.

    Result

    Proceed to

    OK

    NG
    OK

    END (FRONT DOOR WINDOW REGULATOR ASSEMBLY (for Front Passenger Door) WAS DEFECTIVE)

    NG

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

    for LHD:Click hereClick here

    for RHD:Click hereClick here