REAR AIRBAG SENSOR INSTALLATION

CAUTION / NOTICE / HINT

Tip:

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

PROCEDURE

  1. INSTALL REAR AIRBAG SENSOR LH

    1. Turn the engine switch off.

    2. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      Note:

      • After turning the engine switch off, waiting timemay be required before disconnecting the cablefrom the battery terminal. Therefore, make sure toread the disconnecting the cable from the batteryterminal notice before proceeding with work (Click hereClick hereClick here).

      • When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click hereClick hereClick hereClick here).

    3. Install the rear airbag sensor with the nut.

      9.0 N*m

      92 kgf*cm

      80 in.*lbf

      Note:

      • If the rear airbag sensor has been dropped, or there are any cracks, dents or other defects in the case, bracket or connector, replace it with a new one.

      • When installing the rear airbag sensor, be careful that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.

    4. Check that the rear airbag sensor is not loose.

    5. Connect the connector.

  2. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH

    Click hereClick here

  3. INSTALL REAR SEATBACK LOCK CONTROL LEVER BASE LH (w/ Rear No. 2 Seat)

    Click here

  4. INSTALL ASSIST GRIP SUB-ASSEMBLY (w/ Rear No. 2 Seat)

    Click hereClick here

  5. INSTALL ASSIST GRIP PLUG (w/ Rear No. 2 Seat)

    Click hereClick here

  6. INSTALL FRONT DECK SIDE TRIM COVER

    Click hereClick here

  7. INSTALL NO. 1 TONNEAU COVER HOLDER CAP

    Click hereClick here

  8. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

    Click hereClick here

  9. INSTALL REAR NO. 1 SEAT OUTER LAP BELT ANCHOR COVER

    Click hereClick here

  10. INSTALL REAR FLOOR CARPET ASSEMBLY (w/o Rear No. 2 Seat)

    Click hereClick here

  11. INSTALL REAR FLOOR MAT REAR SUPPORT PLATE (w/o Rear No. 2 Seat)

    Click hereClick here

  12. INSTALL NO. 1 DECK BOARD SUB-ASSEMBLY (w/o Rear No. 2 Seat)

    Click hereClick here

  13. INSTALL FRONT LUGGAGE COMPARTMENT TRIM COVER (w/o Rear No. 2 Seat)

    Click hereClick here

  14. INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)

    Click hereClick here

  15. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

    Click hereClick here

  16. INSTALL REAR DOOR SCUFF PLATE LH

    Click hereClick here

  17. INSTALL QUARTER SCUFF PLATE LH (w/ Rear No. 2 Seat)

    Click hereClick here

  18. INSTALL REAR NO. 1 FLOOR STEP COVER (w/ Rear No. 2 Seat)

    Click hereClick here

  19. INSTALL REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat)

    1. Install the rear No. 2 seat assembly (Click here).

  20. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click hereClick hereClick hereClick here).

  21. CHECK SRS WARNING LIGHT

    1. Check the SRS warning light (Click here).