Note
The following inspection procedure of the panoramic view monitor system is described on the assumption that the navigation system is normal. If the navigation system has any malfunction, first proceed with troubleshooting of the navigation system.
Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.
Tech Tips
Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.
| Symptom | Suspected Area | Link |
|---|---|---|
| Display does not switch when the panoramic view monitor switch is pressed. | Refer to "Panoramic View Screen Description" in system description | |
| Proceed to "ECU Power Source Circuit" | ||
| Diagnostic mode - Signal connection check (CAMERA SW check) | ||
| Television camera controller | ||
| Display does not switch to the panoramic view and rear view screen, wide rear view screen, or narrow rear view screen when the shift lever is in R. | Diagnostic mode - Signal connection check (CAN check) | |
| Television camera controller | ||
| Image not displayed on the panoramic view and rear view screen, wide rear view screen or narrow rear view screen when the shift lever is in R. | Proceed to "Image from Camera for Panoramic View Monitor is Abnormal" | |
| Display does not switch to the see through view screen or moving view screen when the panoramic view monitor switch is pressed. | Refer to "Panoramic View Screen Description" in system description | |
| Diagnostic mode - Signal connection check (CAN check) | ||
| Diagnostic mode - Signal connection check (CAMERA SW check) | ||
| Television camera controller | ||
| Image not displayed on the see through view screen or moving view screen when the panoramic view monitor switch is pressed. | Proceed to "Image from Camera for Panoramic View Monitor is Abnormal" | |
| Display does not switch to the panoramic view and wide front view screen or the two-side view screen when the panoramic view monitor switch is pressed. | Proceed to Description "Panoramic View Monitor Screen Display Conditions" | |
| Diagnostic mode - Signal connection check (CAN check) | ||
| Diagnostic mode - Signal connection check (CAMERA SW check) | ||
| Television camera controller | ||
| Image not displayed on the panoramic view and wide front view screen or the two-side view screen when the panoramic view monitor switch is pressed. | Proceed to "Image from Camera for Panoramic View Monitor is Abnormal" | |
| Display does not switch to the retracted screen when the outer mirrors are retracted. | Diagnostic mode - Signal connection check (CAN check) | |
| Television camera controller | ||
| Display does not switch from the retracted screen when the outer mirrors are not in the retracted position. | Diagnostic mode - Signal connection check (CAN check) | |
| Television camera controller |
| Symptom | Suspected Area | Link |
|---|---|---|
| Objects not displayed correctly on the panoramic view monitor screen (color, distorted image). | Proceed to "Image from Camera for Panoramic View Monitor is Abnormal" | |
| Distorted display on panoramic view screen. | Camera view adjustment (calibration) | |
| Television camera controller | ||
| Parking lines do not match at front and rear on panoramic view screen. | Camera view adjustment (calibration) | |
| Television camera controller | ||
| Partial black screen on panoramic view screen. | Proceed to "Image from Camera for Panoramic View Monitor is Abnormal" | |
| Camera view adjustment (calibration) | ||
| Television camera controller | ||
| Area displayed differs from the actual area. | Ensure no door is opened | - |
| Camera view adjustment (calibration) | ||
| Television camera controller |
| Symptom | Suspected Area | Link |
|---|---|---|
| Panoramic view monitor switch night illumination does not illuminate. | Inspect panoramic view monitor switch | |
| Harness or connector | - | |
| The touch function of the screen does not operate for any system. | Proceed to "Touch Panel Switch does not Function" | |
| Television camera controller | ||
| Radio and display receiver assembly | ||
| The touch function of the screen does not operate for the panoramic view monitor system. | Television camera controller | |
| Radio and display receiver assembly |
| Symptom | Suspected Area | Link |
|---|---|---|
| When the vehicle speed increases in the automatic display mode, the panoramic view and wide front view screen or the two-side view screen remains displayed, without switching to the navigation screen. | Television camera controller | |
| The screen display timer function does not operate if the manual display mode is selected. | Refer to "Panoramic View Screen Description" in system description | |
| Television camera controller | ||
| The estimated course lines do not match the vehicle width extension lines when the steering wheel points straight ahead. | Check the steering wheel installation angle | |
| Adjust steering angle | ||
| Camera view adjustment (calibration) | ||
| Television camera controller | ||
| Estimated course lines stop moving before the steering wheel is turned fully left. | Steering angle setting (calibrate stored maximum steering angle) | |
| "!" is displayed and estimated course lines are not displayed. | Check if the luggage compartment door is not open | - |
| Television camera controller | ||
| Replace radio and display receiver assembly | ||
| Estimated course lines are not displayed. | Check the panoramic view monitor screen display mode settings (Check if the estimated course lines display is set to off) | |
| Television camera controller | ||
| "!" is displayed. | Store the steering angle sensor steering neutral point | |
| Diagnostic mode - Signal connection check (CAN check) | ||
| "!" remains displayed after the steering neutral point is stored. | Adjust steering angle | |
| Replace steering sensor | ||
| Television camera controller | ||
| "!" is displayed and all the buttons on the screen are grayed out. | Camera view adjustment (calibration) | |
| Adjust steering angle | ||
| Refer to Navigation System | ||
| "!" is displayed and all the buttons on the screen are grayed out even after television camera controller initialization has been completed. | Television camera controller | |
| Refer to Navigation System | ||
| Guide lines and buttons are not displayed on the panoramic view and rear view screen display screen. | Check if the luggage compartment door is not open | - |
| Check if the luggage compartment light turns on and off normally (If not, refer to Lighting System (Interior) - Problem Symptoms Table) | ||
| Television camera controller | ||
| "CHK" is displayed for an item on the Vehicle Signal Check screen. | Diagnostic mode - Signal connection check | |
| Blind spots in image. | Ensure no door is opened | - |
| Camera view adjustment (calibration) | ||
| Camera boundary lines are poorly connected. | Camera view adjustment (calibration) | |
| Estimated course lines are displaced. | Camera view adjustment (calibration) | |
| Adjust steering angle | ||
| All buttons on the panoramic view monitor are continuously grayed out | Refer to Navigation System |
| Symptom | Suspected Area | Link |
|---|---|---|
| When the parking assist monitor screen is displayed, "RCD unavailable" is displayed. | Correct the steering angle neutral point (Initialization) | |
| Blind spot monitor system | ||
| Rear television camera assembly | ||
| When the parking assist monitor screen is displayed, "RCD malfunction. Visit your dealer" is displayed. | Rear television camera assembly | |
| The indicator does not respond when the mute switch is pushed. | Proceed to "Touch Panel Switch does not Function" | |
| Rear television camera assembly | ||
| Television camera controller | ||
| Radio and display receiver assembly | ||
| When there is a pedestrian in the detection area, no pedestrian is detected. | Refer to "Notes for Rear Camera Detection Function" in precaution | |
| Perform calibration | ||
| Rear television camera assembly | ||
| When there is no pedestrian in the detection area, a pedestrian is detected. | Refer to "Notes for Rear Camera Detection Function" in precaution | |
| Perform calibration | ||
| Rear television camera assembly | ||
| A pedestrian who is in the absolute no detection area* is detected. | Perform calibration | |
| Rear television camera assembly | ||
| A pedestrian is only detected when they are in the absolute detection area*. | Perform calibration | |
| Rear television camera assembly |
*: Refer to "Operation Explanation" in system description