OIL PUMP INSTALLATION


  1. INSTALL TIMING GEAR CASE ASSEMBLY


    1. B007VBQE02

      Install 2 new O-rings to the cylinder block grooves.

    2. B007QYF

      Install the stud bolt.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

    3. Remove any old packing (FIPG) material.

    4. Install the oil pump rotor to the timing gear case.

    5. B007S1RE01

      Install a new gasket to the groove of the timing gear case.

    6. B007U1LE01

      Apply seal packing to the timing gear case as shown in the illustration.

      Seal packing
      Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
      Seal width
      4 mm (0.16 in.)

      Note

      After applying FIPG, install the timing gear case assembly within 3 minutes and then tighten its bolts within 15 minutes.

    7. B007SP1E01

      Install the timing gear case with the union bolt and 8 bolts.

      Torque:
      16 N*m  { 163 kgf*cm, 12 ft.*lbf }
      13 N*m  { 133 kgf*cm, 10 ft.*lbf }

    8. Remove the screw plug.

    9. B007VWL

      Pour approximately 50 cc (1.7 fl.oz) of engine oil into the oil pump.

    10. Reinstall a new gasket and the screw plug.

      Torque:
      42 N*m  { 423 kgf*cm, 31 ft.*lbf }

  2. INSTALL OIL STRAINER SUB-ASSEMBLY


    1. B007Q4W

      Install a new gasket and the oil strainer with the 2 bolts and 2 nuts.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

  3. INSTALL OIL PAN SUB-ASSEMBLY


    1. Remove any old packing (FIPG) material.

    2. B007QHFE03

      Apply seal packing to the oil pan as shown in the illustration.

      Seal packing
      Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
      Seal width
      4.0 mm (0.16 in.)

      Note

      Install the oil pan assembly within 3 minutes and tighten its bolts within 15 minutes after applying FIPG is competed.

    3. B007P4QE01

      Install the oil pan with the 22 bolts and 2 nuts.

      Torque:
      16 N*m  { 163 kgf*cm, 12 ft.*lbf }

    4. Install a new gasket and the drain plug.

      Torque:
      34 N*m  { 347 kgf*cm, 25 ft.*lbf }

  4. INSTALL SUPPLY PUMP GEAR


    1. B007RED

      Install the supply pump with the 2 nuts.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }
    2. B007QQF

      Temporarily install the O-ring and supply pump gear with the nut.

      Tech Tips

      Fit the key (protrusion) of the supply pump to the key slot of the supply pump gear.

    3. B007TS9E01

      Using SST, tighten the nut.

      SST
      09960-10010   ( 09962-01000, 09963-01000 )
      Torque:
      64 N*m  { 653 kgf*cm, 47 ft.*lbf }

  5. INSTALL CRANKSHAFT TIMING GEAR


    1. B007SUUE01

      Face the crankshaft timing gear with timing mark 1 facing forward.

    2. Align the set key on the crankshaft with the key groove of the crankshaft timing gear.

    3. Using SST and a hammer, tap in the timing gear.

      SST
      09223-00010

  6. INSTALL IDLE GEAR SHAFT NO.1


    1. B007U90

      Coat the idle gear shaft No.1 with engine oil as shown in the illustration.

    2. B007VAKE01

      Install the gear shaft.

  7. INSTALL IDLE GEAR NO.1


    1. B007V2EE01

      Align the "5" timing marks of the idle gear and crankshaft timing gear.

    2. Using SST, turn the supply pump gear, and align the "4" timing marks of the idle gear and supply pump gear, and mesh the gears.

      SST
      09960-10010   ( 09962-01000, 09963-00600 )

  8. INSTALL CRANKSHAFT POSITION SENSOR PLATE NO.1


    1. B007P46E01

      Align the set key with the key groove of the sensor plate.

    2. Install the sensor plate with the cup side facing outward.

  9. INSTALL IDLE GEAR THRUST PLATE


    1. B007RJ8

      Face the thrust plate with the protrusion facing outward.

    2. B007S97E01

      Align the bolt holes, and install the thrust plate with the 2 bolts.

      Torque:
      50 N*m  { 510 kgf*cm, 37 ft.*lbf }

  10. INSTALL TIMING CHAIN OR BELT COVER OIL SEAL


    1. B007S96E01

      Using SST and a hammer, tap in a new oil seal until its surface is flush with the timing gear cover edge.

      SST
      09649-17010
      09950-70010   ( 09951-07100 )
      Oil seal depth from the flat-end surface
      0 to -0.5 mm (0 to -0.020 in.)

    2. Apply MP grease to the oil seal lip.

      Note

      Keep the lip clean. Prevent dirt and dust from adhering to that area.

  11. INSTALL TIMING GEAR CASE OR TIMING CHAIN CASE OIL SEAL


    1. B007TCVE01

      Using SST and a hammer, tap in a new oil seal until its surface is flush with the timing gear cover edge.

      SST
      09608-32010
      09950-70010   ( 09951-07100 )
      Oil seal depth from the flat-end surface
      0 to -0.5 mm (0 to -0.020 in.)

    2. Apply MP grease to the oil seal lip.

      Note

      Keep the lip clean. Prevent dirt and dust from adhering to that area.

  12. INSTALL TIMING GEAR CASE


    1. B007PV3

      Remove the service bolt.

    2. B007OGGE01

      Install a new O-ring to the timing gear case assembly.

    3. B007TCYE02

      Apply seal packing to the timing gear case as shown in the illustration.

      Seal packing
      Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
      Seal width
      4.0 mm (0.16 in.)

      Note

      Install the timing gear case within 3 minutes and tighten its bolts within 15 minutes after applying FIPG is competed.

    4. B007TVX

      Install the timing gear case with the 14 bolts and 2 nuts.

      Torque:
      13 N*m  { 133 kgf*cm, 10 ft.*lbf }

  13. INSTALL WATER PUMP ASSEMBLY


    1. B007UVA

      Install a new gasket and the water pump with the 5 bolts and 2 nuts.

      Torque:
      13 N*m  { 133 kgf*cm, 10 ft.*lbf }

  14. INSTALL TIMING BELT COVER NO.2


    1. B007V11E01

      Apply seal packing to the timing gear cover as shown in the illustration.

      Seal packing
      Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

      Note

      Install the timing belt No. 2 cover within 3 minutes and tighten its bolts and nut within 15 minutes after applying FIPG is competed.

    2. B007R1O

      Install the timing belt No. 2 cover with the 4 bolts and nut.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

  15. INSTALL CAMSHAFT TIMING PULLEY


    1. Install the set key to the key groove of the camshaft.

    2. Align the set key with the key groove of the timing pulley.

    3. B007V8T

      Hold the hexagon portion of the camshaft, and install the timing pulley with the bolt.

      Torque:
      98 N*m  { 1,000 kgf*cm, 72 ft.*lbf }

  16. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY


    1. B007WARE03

      Install 4 new No. 3 cylinder head cover gaskets to the cylinder head cover as shown in the illustration.

      Note


      • Do not install the gaskets at an angle.

      • Keep the lip of the gasket free from foreign materials.

    2. Install a new cylinder head cover gasket to the cylinder head cover.

    3. B007T7DE01

      Apply seal packing to the cylinder head as shown in the illustration.

      Seal packing
      Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

      Note

      After applying the seal packing, parts must be assembled within 3 minutes, and then tighten them within 15 minutes.

    4. B007U7G

      Install the cylinder head cover with 10 bolts and 2 nuts. Uniformly tighten the bolts and nuts in several steps.

      Torque:
      9.0 N*m  { 92 kgf*cm, 80 in.*lbf }

  17. INSTALL NOZZLE HOLDER SEAL


    1. B007SDRE01

      Install 4 new holder seals.

  18. INSTALL OIL FILLER CAP SUB-ASSEMBLY


    1. B007RVRE01

      Install the oil filler cap.

  19. INSTALL ENGINE OIL LEVEL SENSOR


    1. Set a new gasket, and then install the engine oil level sensor with the 4 bolts.

      Torque:
      7.0 N*m  { 71 kgf*cm, 52 in.*lbf }

  20. INSTALL CRANKSHAFT POSITION SENSOR


    1. B007V42

      Apply a light coat of engine oil to the O-ring of the crankshaft position sensor.

    2. B007THJ

      Install the crankshaft position sensor with the bolt.

      Torque:
      8.5 N*m  { 87 kgf*cm, 75 in.*lbf }

      Note

      Be careful that the O-ring is not cracked or jammed when installing the crankshaft position sensor.

    3. Connect the 3 wire harness clamps.

    4. B007VEA

      Connect the crankshaft position sensor connector to the vacuum pipe No.1.

    5. Connect the crankshaft position sensor connector.

  21. INSTALL CAMSHAFT POSITION SENSOR


    1. B007T9B

      Apply a light coat of engine oil to the O-ring of the camshaft position sensor.

    2. B007VA3

      Install the camshaft position sensor with the bolt.

      Torque:
      8.5 N*m  { 87 kgf*cm, 75 in.*lbf }

      Note

      Be careful that the O-ring is not cracked or jammed when installing the camshaft position sensor.

    3. Connect the camshaft position sensor connector.

  22. INSTALL VACUUM PUMP ASSEMBLY


    1. Apply the engine oil to the 2 new O-rings.

    2. Install the 2 O-rings to the vacuum pump assembly.

    3. B007W8C

      Install the vacuum pump assembly to the engine with the 2 nuts.

      Torque:
      21 N*m  { 210 kgf*cm, 15 ft.*lbf }

      Note


      • Do not drop the vacuum pump packing.

      • Make sure that the vacuum pump assembly is securely installed.

    4. B007W3F

      Install the vacuum pump union and the 2 new gaskets with the union bolt.

      Torque:
      14 N*m  { 140 kgf*cm, 10 ft.*lbf }

      Note

      Check that the stopper of the vacuum pump union is securely holding on the vacuum pump assembly.

    5. Connect the 2 hoses with the clip to the vacuum pump.

      Note

      Set the vacuum hose so the white marking facing upward.

  23. INSTALL CRANKSHAFT PULLEY


    1. B007VHLE01

      Tighten the bolt holding the crankshaft pulley with SST.

      SST
      09213-58013
      09330-00021
      Torque:
      365 N*m  { 3,722 kgf*cm, 270 ft.*lbf }

  24. INSTALL TIMING BELT IDLER SUB-ASSEMBLY NO.1.


    1. B007SOT

      Using a 10 mm hexagon wrench, install a new washer and the timing belt idler with the bolt.

      Torque:
      35 N*m  { 357 kgf*cm, 26 ft.*lbf }

      Note

      Do not reuse the washer.

  25. INSTALL V-RIBBED BELT TENSIONER ASSEMBLY


    1. B007QFJE01

      Temporarily install the V-ribbed belt tensioner with the 4 bolts.

      Tech Tips

      Make sure that the V-ribbed belt tensioner is in contact with the engine block at points A shown in the illustration.

    2. Tighten the V-ribbed belt tensioner with the 4 bolts.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

  26. INSTALL GENERATOR ASSEMBLY


    1. B007TSLE01

      Install the generator assembly with the bolt.

      Torque:
      62 N*m  { 632 kgf*cm, 46 ft.*lbf }

    2. Install the generator wire to terminal B with the nut.

      Torque:
      9.8 N*m  { 100 kgf*cm, 87 in.*lbf }

    3. Install the terminal cap.

    4. Connect the generator connector.

  27. INSTALL GENERATOR BRACKET


    1. B007Q8BJ01

      Install the generator bracket with the 2 bolts.

      Torque:
      36 N*m  { 367 kgf*cm, 27 ft.*lbf }

  28. INSTALL IDLE PULLEY ASSEMBLY


    1. Install the idler pulley and washers with the bolt.

      Torque:
      45 N*m  { 459 kgf*cm, 33 ft.*lbf }

  29. INSTALL COMPRESSOR BRACKET


    1. B007S7ZE02

      Temporarily install the compressor bracket with the 4 bolts.

      Tech Tips

      Make sure that the compressor bracket is in contact with the engine block.

    2. Install the compressor bracket by tightening the 4 bolts as shown in the illustration.

      Torque:
      45 N*m  { 459 kgf*cm, 33 ft.*lbf }

  30. INSTALL PUMP DRIVE SHAFT PULLEY

    Click here

  31. CHECK PUMP DRIVE SHAFT THRUST CLEARANCE


    1. B007QNK

      Push the pump drive shaft pulley back and forth to check a thrust clearance of the injection pump drive shaft.

      Thrust clearance
      0.15 to 0.55 mm (0.0059 to 0.0217 in.)

      Note

      Make sure that the crankshaft pulley's notch is at 30 degree in the counterclockwise direction form the TDC position.

      Tech Tips

      If there is not thrust clearance, disassemble and reassemble the injection pump and pump drive shaft pulley.

  32. INSTALL COMMON RAIL ASSEMBLY


    1. B007RO1E01

      Install the common rail assembly with the 2 bolts.

      Torque:
      38 N*m  { 387 kgf*cm, 28 ft.*lbf }

    2. Connect the fuel hose to the fuel pressure limiter.

    3. Connect the fuel pressure sensor connector.

  33. INSTALL FUEL INLET PIPE SUB-ASSEMBLY

    Note


    • When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket, or timing gear case with a new one, replace the fuel inlet pipe.

    • Be careful not to adhere dusts, dirt or any other materials onto the joint area of the fuel inlet pipe.


    1. Temporarily install the fuel inlet pipe.

    2. Using SST, tighten the injection pipe on the common rail side.

      SST
      09023-12701
      Torque:
      32 N*m  { 326 kgf*cm, 24 ft.*lbf, for use with SST }

    3. Using SST, tighten the injection pipe on the supply pump side.

      SST
      09023-12701
      Torque:
      32 N*m  { 326 kgf*cm, 24 ft.*lbf, for use with SST }

  34. INSTALL INJECTION PIPE

    SST
    09023-12701

    Note


    • When replacing the fuel injector, common rail, or cylinder head with a new one, replace injection pipes No. 1, No. 2, No. 3, and No. 4.

    • Keep clean the joint of the injection pipe.


    1. Install the injection pipes.


      1. B007QK6

        Temporarily install the 4 injection pipes.

      2. B007SS6

        Install the injection pipe clamp No.3 in 2 nuts.

        Torque:
        5.0 N*m  { 51 kgf*cm, 44 in.*lbf }
      3. B007QK6E01

        Fasten the union sequentially, from the injection pipe common rail to the injector, using SST.

        SST
        09023-12701
        Torque:
        Use union nut wrench and torque wrench
        32 N*m  { 326 kgf*cm, 24 ft.*lbf }

  35. INSTALL OIL LEVEL GAGE GUIDE


    1. Install a new O-ring to the oil level gauge guide.

    2. Apply a light coat of engine oil to the O-ring.

    3. Install the oil level gauge guide with the bolt.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

    4. Install the oil level gauge.

  36. INSTALL EGR PIPE SUB-ASSEMBLY NO.1


    1. B007W39

      Install 2 new gaskets to the cylinder head and the EGR pipe sub-assembly No.1 as shown in the illustration.

    2. B007S6J

      Install the EGR pipe with the 2 bolts and the 2 nuts.

      Torque:
      13 N*m  { 133 kgf*cm, 10 ft.*lbf }
    3. B007QY1

      Connect the fuel pressure sensor connector.

  37. INSTALL FAN PULLEY


    1. Install the fan pulley with the 4 nuts.

      Torque:
      23 N*m  { 235 kgf*cm, 17 ft.*lbf }

  38. PERFORM PISTON AND VALVE BREAK PREVENT WORK


    1. B007R2I

      When turning the camshaft with the timing belt removed, turn the crankshaft 90° counterclockwise.

      Note

      When installing the timing belt, it is necessary to return the camshaft to the timing marks and then turn the crankshaft clockwise so that it aligns with the timing marks as shown in the illustration.

  39. INSTALL TIMING BELT


    1. B007PVSE01

      Check that the timing marks are aligned as shown in the illustration.

    2. Install the timing belt to pump drive shaft pulley, camshaft timing pulley and timing belt idler No.1 in sequence.

    3. B007W58

      Set the tensioner to the press upright.

      Note


      • Do not allow the rod end to scratch and deform.

      • Press the tensioner rod in upward.

      • Protect a tip of the push rod with a rag in order to prevent damage.

    4. Using a press, slowly apply 981 to 9,807 N (100 to 1,000 kgf, 220 to 2,205 lbf) of force to the push rod.

      Note

      Do not apply loads 981 to 9,807 N (100 to 1,000 kgf, 220 to 2,205 lbf) or more on the push rod.

    5. Align the holes of push rod and housing, pass a 1.27 mm hexagon wrench through the holes to keep the setting position of the push rod.

    6. Temporarily install the timing belt tensioner with the 2 bolts while pushing the idler pulley toward the timing belt.

    7. Tighten the 2 bolts.

      Torque:
      13 N*m  { 133 kgf*cm, 10 ft.*lbf }

      Note

      Uniformly tighten the 2 bolts and install the tensioner

    8. Remove the 1.5 mm hexagon wrench from the tensioner.

    9. B007P0XE01

      Turn the crankshaft in the clockwise direction twice, check that the timing marks are aligned as shown in the illustration.

  40. INSTALL TIMING BELT COVER NO.1


    1. B007R8N

      Install the timing belt No.1 cover with the 6 bolts.

      Torque:
      6.0 N*m  { 61 kgf*cm, 53 in.*lbf }

    2. Install the wire harness clamp.

  41. INSTALL VANE PUMP ASSEMBLY


    1. Install a new vane pump O-ring to the vane pump assembly.

    2. B007QBUE01

      Install the vane pump assembly with the 2 nuts.

      Torque:
      39 N*m  { 398 kgf*cm, 29 ft.*lbf }

      Note

      Make sure that the vane pump O-ring is not caught between other parts.

  42. INSTALL ENGINE ASSEMBLY

    Click here