MANUAL TRANSAXLE UNIT COMPONENTS
ILLUSTRATION
*1 |
BACK-UP LIGHT SWITCH ASSEMBLY |
*2 |
DRAIN PLUG |
*3 |
FLOOR SHIFT SELECTING BELL CRANK ASSEMBLY |
*4 |
NEUTRAL POSITION SWITCH |
*5 |
NO. 1 LOCK BALL ASSEMBLY |
*6 |
NO. 2 LOCK BALL ASSEMBLY |
*7 |
SHIFT AND SELECT LEVER ASSEMBLY |
*8 |
SHIFT AND SELECT LEVER SHAFT NEEDLE ROLLER BEARING |
*9 |
SHIFT AND SELECT LEVER SHAFT STRAIGHT PIN |
*10 |
SHIFT GATE PIN |
*11 |
TRANSAXLE CASE OIL SEAL |
*12 |
TRANSMISSION CASE OIL SEAL |
*13 |
SPRING |
*14 |
GASKET |
*15 |
O-RING |
- |
- |
 |
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
 |
MP grease |
 |
Toyota Genuine 1344, Three Bond 1344 or equivalent |
★ |
Precoated part |
- |
- |
ILLUSTRATION
*1 |
CLUTCH RELEASE BEARING ASSEMBLY |
*2 |
CLUTCH RELEASE FORK BOOT |
*3 |
CLUTCH RELEASE FORK SUB-ASSEMBLY |
*4 |
CONTROL CABLE BRACKET |
*5 |
MANUAL TRANSMISSION CASE PLUG |
*6 |
MANUAL TRANSMISSION FILLER PLUG |
*7 |
RELEASE FORK SUPPORT |
*8 |
REVERSE IDLER GEAR SHAFT BOLT |
*9 |
SHIFT DETENT BALL |
*10 |
RELEASE BEARING HUB CLIP |
*11 |
SHIFT DETENT BALL COMPRESSION SPRING |
*12 |
NO. 1 SHIFT DETENT BALL SPRING SEAT |
*13 |
DETENT BALL PLUG |
*14 |
GASKET |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
|
Release hub grease |
|
Clutch spline grease |
 |
Toyota Genuine 1344, Three Bond 1344 or equivalent |
★ |
Precoated part |
ILLUSTRATION
*1 |
FRONT DIFFERENTIAL CASE ASSEMBLY |
*2 |
FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING |
*3 |
FRONT DIFFERENTIAL CASE REAR OUTER RACE BEARING |
*4 |
FRONT INPUT SHAFT BEARING |
*5 |
FRONT NO. 2 OUTPUT SHAFT BEARING OUTER RACE |
*6 |
FRONT OUTPUT SHAFT BEARING |
*7 |
MANUAL TRANSMISSION CASE |
*8 |
NO. 1 OIL RECEIVER PIPE |
*9 |
OUTPUT SHAFT COVER |
*10 |
REAR NO. 2 OUTPUT SHAFT BEARING OUTER RACE |
*11 |
REAR OUTPUT SHAFT BEARING SHIM |
*12 |
TRANSAXLE CASE OIL SEAL |
*13 |
TRANSMISSION MAGNET |
*14 |
TRANSMISSION OIL SEPARATOR |
*15 |
FRONT TRANSAXLE CASE |
*16 |
FRONT DIFFERENTIAL CASE REAR SHIM |
*17 |
REAR OUTPUT SHAFT BEARING SHAFT SNAP RING |
*18 |
REAR INPUT SHAFT BEARING SHAFT SNAP RING |
*19 |
INPUT SHAFT |
*20 |
NO. 2 OUTPUT SHAFT ASSEMBLY |
*21 |
NO. 1 OUTPUT SHAFT ASSEMBLY |
*22 |
BEARING LOCK PLATE |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
|
MP grease |
- |
- |
ILLUSTRATION
*1 |
1ST AND 2ND SHIFT FORK SHAFT |
*2 |
3RD AND 4TH SHIFT FORK SHAFT |
*3 |
5TH AND 6TH SHIFT FORK SHAFT |
*4 |
MANUAL TRANSMISSION CASE STRAIGHT PIN |
*5 |
NO. 1 GEAR SHIFT FORK |
*6 |
NO. 2 GEAR SHIFT FORK |
*7 |
NO. 3 GEAR SHIFT FORK |
*8 |
NO. 5 GEAR SHIFT FORK SHAFT |
*9 |
REVERSE IDLER GEAR |
*10 |
REVERSE SHIFT FORK |
*11 |
REVERSE SHIFT FORK SHAFT |
*12 |
SHIFT ARM |
*13 |
SHIFT FORK SHAFT BEARING |
*14 |
TRANSMISSION OIL SEPARATOR |
*15 |
NO. 2 GEAR SHIFT HEAD |
*16 |
PIN |
*17 |
NO. 3 GEAR SHIFT HEAD |
*18 |
REVERSE IDLER GEAR SHAFT |
*19 |
REVERSE IDLER THRUST WASHER |
*20 |
NEEDLE ROLLER BEARING |
*21 |
E-RING |
*22 |
FRONT TRANSAXLE CASE |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
|
MP grease |
|
Toyota Genuine 1344, Three Bond 1344 or equivalent |
★ |
Precoated part |
- |
- |