CAMSHAFT COMPONENTS
ILLUSTRATION
*1 |
ENGINE ROOM SIDE COVER |
*2 |
ENGINE ROOM SIDE COVER LH |
*3 |
LOWER FRONT BUMPER COVER |
*4 |
NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY |
*5 |
REAR ENGINE UNDER COVER ASSEMBLY |
*6 |
TRANSMISSION UNDER COVER |
 |
Specified torque: N*m (kgf*cm, ft.*lbf) |
- |
- |
ILLUSTRATION
*1 |
AIR CLEANER CAP AND HOSE |
*2 |
AIR CLEANER CASE SUB-ASSEMBLY |
*3 |
BATTERY |
*4 |
BATTERY TRAY |
*5 |
UPPER RADIATOR SUPPORT SEAL |
*6 |
V-BANK COVER SUB-ASSEMBLY |
*7 |
WIRING HARNESS CLAMP BRACKET |
*8 |
BATTERY HOLD DOWN CLAMP |
*9 |
WIRE HARNESS |
*10 |
VACUUM HOSE |
*11 |
PCV HOSE |
*12 |
AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY |
|
Specified torque: N*m (kgf*cm, ft.*lbf) |
- |
- |
ILLUSTRATION
*1 |
FAN SHROUD |
*2 |
NO. 1 RADIATOR HOSE |
*3 |
NO. 2 RADIATOR HOSE |
*4 |
OIL COOLER TUBE |
*5 |
RADIATOR RESERVOIR ASSEMBLY |
*6 |
FAN AND GENERATOR V BELT |
*7 |
FAN PULLEY |
*8 |
FAN WITH FLUID COUPLING |
|
Specified torque: N*m (kgf*cm, ft.*lbf) |
- |
- |
ILLUSTRATION
*1 |
ENGINE OIL LEVEL DIPSTICK GUIDE |
*2 |
IGNITION COIL ASSEMBLY |
*3 |
INTAKE AIR SURGE TANK |
*4 |
VANE PUMP ASSEMBLY |
*5 |
NO. 2 SURGE TANK STAY |
*6 |
NO. 1 VACUUM SWITCHING VALVE CONNECTOR |
*7 |
NO. 1 FUEL VAPOR FEED HOSE |
*8 |
NO. 1 VENTILATION HOSE |
*9 |
WIRE HARNESS |
*10 |
NO. 1 SURGE TANK STAY |
*11 |
HEATER WATER HOSE |
*12 |
NO. 4 WATER BY-PASS HOSE |
*13 |
NO. 5 WATER BY-PASS HOSE |
*14 |
ENGINE OIL LEVEL DIPSTICK |
*15 |
THROTTLE BODY BRACKET |
*16 |
THROTTLE BODY CONNECTOR |
*17 |
O-RING |
*18 |
GASKET |
|
Specified torque: N*m (kgf*cm, ft.*lbf) |
● |
Non-reusable part |
ILLUSTRATION
*A |
for Separate Type |
*B |
for Integrated Type |
*1 |
NO. 2 IDLER PULLEY SUB-ASSEMBLY |
*2 |
IDLER PULLEY COVER PLATE |
*3 |
NO. 2 IDLER PULLEY COVER PLATE |
- |
- |
|
Specified torque: N*m (kgf*cm, ft.*lbf) |
- |
- |
ILLUSTRATION
*1 |
CYLINDER HEAD COVER SUB-ASSEMBLY |
*2 |
CYLINDER HEAD COVER SUB-ASSEMBLY LH |
*3 |
FUEL PIPE SUB-ASSEMBLY |
*4 |
GENERATOR ASSEMBLY |
*5 |
NO. 1 OIL PIPE |
*6 |
NO. 2 EXHAUST MANIFOLD HEAT INSULATOR |
*7 |
NO. 2 OIL PIPE |
*8 |
REAR CYLINDER HEAD COVER |
*9 |
WATER BY-PASS PIPE SUB-ASSEMBLY |
*10 |
SEAL WASHER |
*11 |
CYLINDER HEAD COVER GASKET |
*12 |
SEAL WASHER |
*13 |
OIL CONTROL VALVE FILTER LH |
*14 |
OIL CONTROL VALVE FILTER RH |
*15 |
NO. 2 CYLINDER HEAD COVER GASKET |
*16 |
GENERATOR BRACKET |
*17 |
GASKET |
- |
|
|
Specified torque: N*m (kgf*cm, ft.*lbf) |
● |
Non-reusable part |
ILLUSTRATION
*1 |
CAMSHAFT |
*2 |
CAMSHAFT BEARING CAP (for Bank 1) |
*3 |
CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY (for Bank 1) |
*4 |
CAMSHAFT TIMING GEAR ASSEMBLY (for Bank 1) |
*5 |
NO. 1 CHAIN SUB-ASSEMBLY |
*6 |
NO. 1 CHAIN TENSIONER ASSEMBLY |
*7 |
NO. 2 CAMSHAFT |
*8 |
NO. 3 CAMSHAFT |
*9 |
NO. 4 CAMSHAFT |
*10 |
TIMING CHAIN COVER PLATE |
*11 |
NO. 2 CHAIN SUB-ASSEMBLY (for Bank 1) |
*12 |
NO. 2 CHAIN SUB-ASSEMBLY (for Bank 2) |
*13 |
CAMSHAFT BEARING CAP (for Bank 2) |
*14 |
CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY (for Bank 2) |
*15 |
NO. 2 CHAIN TENSIONER ASSEMBLY |
*16 |
NO. 3 CHAIN TENSIONER ASSEMBLY |
*17 |
CAMSHAFT TIMING GEAR ASSEMBLY (for Bank 2) |
*18 |
GASKET |
|
Specified torque: N*m (kgf*cm, ft.*lbf) |
● |
Non-reusable part |