TELEMATICS SYSTEM(for ERA-GLONASS), Diagnostic DTC:B15C0, B15C1

DTC Code DTC Name
B15C0 GPS Antenna Disconnected (Short)
B15C1 GPS Antenna Disconnected (Open)

DESCRIPTION

These DTCs are stored when a malfunction occurs in the GPS antenna.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15C0 GPS Antenna Disconnected (Short)

Current to the roof antenna assembly is lower than the malfunction threshold for 20 seconds when the engine switch is on (IG).

(Short circuit)


  • Telematics Transceiver

  • Roof antenna assembly

  • Antenna cord sub-assembly (Floor)

  • Harness or Connector

B15C1 GPS Antenna Disconnected (Open)

Current for roof antenna assembly is higher than the malfunction threshold for 20 seconds when the engine switch is on (IG).

(Open circuit)


  • Telematics Transceiver

  • Roof antenna assembly

  • Antenna cord sub-assembly (Floor)

  • Harness or Connector

WIRING DIAGRAM

B006ANXE05

CAUTION / NOTICE / HINT

Note


  • Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.

    Click here

  • When replacing the telematics transceiver, make sure to replace it with a new one.

PROCEDURE


  1. CHECK FOR DTC


    1. Turn the engine switch off.

    2. Connect the GTS to the DLC3.

    3. Turn the engine switch on (IG) and wait for 20 seconds.

    4. Turn the GTS on.

    5. Check for DTCs and check that no DTCs are output.

      Click here


      Body Electrical > Telematics > Trouble Codes
      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG

    OK
    NG
  2. INSPECT ANTENNA CORD SUB-ASSEMBLY (FLOOR)


    1. B006AB1C04
      *a

      Front view of wire harness connector

      (to Roof Antenna Assembly)

      *b

      Front view of wire harness connector

      (to Wire Harness)

      Disconnect the antenna connector from the roof antenna assembly.

    2. Disconnect the antenna connector from the wire harness.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A-2 - G153-2 (ANT2) Always Below 1 Ω
      A-2a - G153-2a Always Below 1 Ω
      A-2 - Body ground Always 10 kΩ or higher
      A-2a - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG
    OK
  3. CHECK HARNESS AND CONNECTOR (ANTENNA CORD SUB-ASSEMBLY [FLOOR] - TELEMATICS TRANSCEIVER)


    1. B006AL9C01
      *a

      Front view of wire harness connector

      (to Antenna Cord Sub-assembly [Floor])

      *b

      Front view of wire harness connector

      (to Telematics Transceiver)

      Disconnect the antenna connector from the antenna cord sub-assembly (floor).

    2. Disconnect the antenna connector from the telematics transceiver.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G153-2 (ANT2) - G154-1 (ANT2) Always Below 1 Ω
      G153-2a - G154-1a Always Below 1 Ω
      G153-2 (ANT2) - Body ground Always 10 kΩ or higher
      G153-2a - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG
    OK
  4. CHECK ROOF ANTENNA ASSEMBLY


    1. Replace the roof antenna assembly with a known good one.

      Click here

    2. Clear the DTCs.

      Click here


      Body Electrical > Telematics > Clear DTCs
    3. Recheck for DTCs and check that no DTCs are output.

      Click here


      Body Electrical > Telematics > Trouble Codes
      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG

    OK
    NG
  5. REPLACE TELEMATICS TRANSCEIVER


    1. Replace the telematics transceiver with a new one.

      Click here

      Result
      Proceed to
      NEXT

    NEXT