LIGHTING SYSTEM Interior Light Auto Cut Circuit

DESCRIPTION

The main body ECU (multiplex network body ECU) controls operation of the DOME CUT relay in order to supply power to the interior lights. When the battery saving function operates while the interior lights are on, the main body ECU (multiplex network body ECU) opens the DOME CUT relay to turn off the lights.

WIRING DIAGRAM

A001WOIE04

CAUTION / NOTICE / HINT

Note


  • Inspect the fuses for circuits related to this system before performing the following procedure.

  • Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin*1.


    • *1: w/ Entry and Start System

PROCEDURE


  1. PERFORM ACTIVE TEST USING GTS


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Main Body / Active Test.

    5. Perform the Active Test according to the display on the GTS.


      Body Electrical > Main Body > Active Test
      Tester Display Measurement Item Control Range Diagnostic Note
      Relay for Interior Light Auto Cut Function DOME CUT relay ON or OFF

      When performing this active test, turn all the interior lights on.


      • ON: DOME CUT relay off (interior lights turn off)

      • OFF: DOME CUT relay on (interior lights turn on)

      Body Electrical > Main Body > Active Test
      Tester Display
      Relay for Interior Light Auto Cut Function
      OK
      All of the interior lights turn off when ON is selected.
      Result
      Proceed to
      OK
      NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

  2. CHECK HARNESS AND CONNECTOR (POWER SOURCE - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)


    1. Disconnect the 3K instrument panel junction block assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      3K-1 - Body ground Always 11 to 14 V
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


    1. Remove the instrument panel junction block assembly.


    2. Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


    3. Measure the voltage and resistance according to the value(s) in the table below.

      A001WNHC06
      *a

      Component without harness connected

      (Instrument Panel Junction Block Assembly)

      		 - -
      Standard Voltage
      Tester Connection Condition Specified Condition
      3H-19 - Battery negative terminal

      Battery positive (+) → 3K-1

      Battery negative (-) → MB-23 (DOMR)

      		 11 to 14 V
      3D-9 - Battery negative terminal

      Battery positive (+) → 3K-1

      Battery negative (-) → MB-23 (DOMR)

      		 11 to 14 V
      Standard Resistance
      Tester Connection Condition Specified Condition
      3K-1 - 3H-19 Always 10 kΩ or higher
      3K-1 - 3D-9 Always 10 kΩ or higher
      Result
      Result Proceed to
      OK (for LHD) A
      OK (for RHD) B
      NG (for LHD) C
      NG (for RHD) D

    A

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here

    B

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here

    C

    REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY Click here

    D

    REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY Click here