PARKING BRAKE CABLE REMOVAL

CAUTION / NOTICE / HINT

Tip:

  • The following procedure is for the No. 1 parking brake cable assembly and No. 3 parking brake cable assembly.

  • Use the same procedure for the No. 3 parking brake cable assembly and No. 2 parking brake cable assembly.

PROCEDURE

  1. REMOVE PARKING BRAKE LEVER SUB-ASSEMBLY

    Click here

  2. REMOVE PARKING BRAKE CABLE END STOPPER

    1. C278566

      Push the No. 1 parking brake cable assembly and rotate the cable end 90°.

    2. C278570

      Pull the No. 1 parking brake cable assembly out of the parking brake equalizer.

    3. Remove the parking brake cable end stopper.

  3. REMOVE NO. 1 PARKING BRAKE CABLE ASSEMBLY

    1. C271173

      Remove the No. 2 wire adjusting nut.

    2. C271174

      Pull up the parking brake lever sub-assembly claw.

      Note:

      Do not damage the No. 1 parking brake cable assembly.

    3. Remove the No. 1 parking brake cable assembly from the parking brake lever sub-assembly.

  4. REMOVE FRONT EXHAUST PIPE ASSEMBLY

    for 1AD-FTV:Click here

    for 1ND-TV:Click here

  5. REMOVE CENTER EXHAUST PIPE ASSEMBLY (for Front Side)

    for 1NR-FE:Click here

  6. REMOVE FRONT EXHAUST PIPE ASSEMBLY (TWC: Front and Rear Catalyst)

    for 1ZR-FAE:Click here

    for 1ZR-FE:Click here

    for 2ZR-FE:Click here

  7. REMOVE FRONT NO. 1 FLOOR HEAT INSULATOR

    1. C269919

      Remove the 3 nuts and front No. 1 floor heat insulator.

  8. REMOVE FRONT NO. 2 FLOOR HEAT INSULATOR

    1. C287579C01

      *A

      for Sedan

      *B

      except Sedan

      Remove the 3 nuts and front No. 2 floor heat insulator.

  9. REMOVE REAR FLOOR SIDE MEMBER COVER LH (for LH Side)

    for Torsion Beam Type Suspension (w/ Cover):Click here

    for Double Wishbone Type Suspension:Click here

  10. REMOVE REAR FLOOR SIDE MEMBER COVER RH (for RH Side)

    for Torsion Beam Type Suspension (w/ Cover):Click here

    for Double Wishbone Type Suspension:Click here

  11. REMOVE PARKING BRAKE LEVER PROTECTOR (for Double Wishbone Type Suspension)

    1. C274284

      Remove the parking brake lever protector.

  12. REMOVE NO. 3 PARKING BRAKE CABLE ASSEMBLY (for Torsion Beam Type Suspension)

    1. Remove the 5 bolts, disengage the clamp and remove the No. 3 parking brake cable assembly.

      C271177
    2. C149798

      Pull out the No. 3 parking brake cable assembly to the outside of the body.

    3. C271175

      Separate the No. 3 parking brake cable assembly from the rear disc brake cylinder assembly.

    4. C271176C02

      *1

      Rear Disc Brake Cylinder Assembly

      *a

      Clip

      Disengage the clip and remove the No. 3 parking brake cable assembly.

  13. REMOVE NO. 3 PARKING BRAKE CABLE ASSEMBLY (for Double Wishbone Type Suspension)

    1. Remove the 5 bolts, disengage the clamp and remove the No. 3 parking brake cable assembly.

      C271178
    2. C149798

      Pull out the No. 3 parking brake cable assembly to the outside of the body.

    3. C271179

      Separate the No. 3 parking brake cable assembly from the rear disc brake cylinder assembly.

    4. C271180C02

      *1

      Rear Disc Brake Cylinder Assembly

      *a

      Clip

      Disengage the clip and remove the No. 3 parking brake cable assembly.

  14. REMOVE NO. 1 PARKING BRAKE CABLE CLAMP

    1. C158971

      for Separate type No. 1 parking brake cable clamp:

      1. Disengage the 2 claws to remove the No. 1 parking brake cable clamp from the No. 3 parking brake cable assembly.

    2. for One-piece type No. 1 parking brake cable clamp:

      1. Using pliers or equivalent, remove the No. 1 parking brake cable clamp from the No. 3 parking brake cable assembly.

        Tip:

        The No. 1 parking brake cable clamp cannot be reused once removed. Make sure to remove it from the No. 3 parking brake cable assembly.