BRAKE CONTROL SYSTEM


  1. OPERATION


    1. Engine Output Control during TRC or VSC Operation


      1. During the TRC or VSC operation, the skid control ECU outputs the engine output control signal to the ECM. Upon receiving this signal, the ECM inhibits the engine output.

        B002317E01

    2. ABS with EBD


      1. Based on the signals received from the 4 speed sensors, the skid control ECU calculates each wheel speed and deceleration, and checks wheel slipping conditions. According to the slipping condition, the skid control ECU controls the pressure holding valve and pressure reduction valve in order to adjust the fluid pressure of each wheel cylinder in the following 3 modes: pressure reduction, pressure holding and pressure increase modes.

        B0022YMC03
        *1 Port A *2 Port B
        *3 Pressure Holding Solenoid Valve *4 Pressure Reduction Solenoid Valve
        *a Increase Mode *b Holding Mode
        *c Reduction Mode *d to Wheel Cylinder
        *e to Reservoir and Pump *f from Wheel Cylinder
        Not Activated Normal Braking - -
        Activated Increase Mode Holding Mode Reduction Mode
        Pressure Holding Solenoid Valve (Port A) OFF (Open) ON (Close) ON (Close)
        Pressure Reduction Solenoid Valve (Port B) OFF (Close) OFF (Close) ON (Open)
        Wheel Cylinder Pressure Increased Held Reduced

    3. Brake Assist


      1. In the event of emergency braking, the skid control ECU determines the driver's intentions based on the speed of the pressure increase in the master cylinder detected by the master cylinder pressure sensor signal. If the skid control ECU judges the need for additional brake assist, pressure to supplement the amount provided by the master cylinder is generated by the pump in the brake actuator and directed to each wheel cylinder.

        B0022XKE02
        B0022YGC01
        *1 Brake Master Cylinder Sub-assembly *2 Brake Actuator Assembly
        *3 Master Cylinder Pressure Sensor *4 Pump
        *5 Reservoir *6 Front Brake Caliper (Right Side)
        *7 Rear Brake Caliper (Left Side) *8 Rear Brake Caliper (Right Side)
        *9 Front Brake Caliper (Left Side) - -

      2. Each valve operates as shown below:

        Item Port Brake Assist Not Activated Brake Assist Activated
        Master Cylinder Cut Solenoid Valve (1), (4) (A), (D) OFF (Open) ON*
        Reservoir Cut Solenoid Valve (2), (3) (B), (C) OFF (Closed) ON (Open)
        Front Brakes Pressure Holding Solenoid Valve (5), (8) (E), (H) OFF (Open) OFF (Open)
        Pressure Reduction Solenoid Valve (9), (12) (I), (L) OFF (Closed) OFF (Closed)
        Rear Brakes Pressure Holding Solenoid Valve (6), (7) (F), (G) OFF (Open) OFF (Open)
        Pressure Reduction Solenoid Valve (10), (11) (J), (K) OFF (Closed) OFF (Closed)
        Pump OFF ON

        *: Hydraulic pressure is controlled by continuously cycling the solenoid valves between open and closed, according to the operating conditions.

    4. TRC


      1. The fluid pressure generated by the pump is regulated by the master cylinder cut solenoid valves to achieve the required pressure. Thus, the brakes for the drive wheels are controlled in the following 3 modes: pressure reduction, pressure holding, and pressure increase modes, to control slippage of the drive wheels.

      2. The diagram shows the hydraulic circuit in pressure increase mode when TRC is activated. The pressure holding solenoid valves and the pressure reduction solenoid valves are turned ON/OFF according to the ABS and EBD operation pattern.

        B0023GNE04
        B0023K2C03
        *1 Brake Master Cylinder Sub-assembly *2 Brake Actuator Assembly
        *3 Master Cylinder Pressure Sensor *4 Pump
        *5 Reservoir *6 Front Brake Caliper (Right Side)
        *7 Rear Brake Caliper (Left Side) *8 Rear Brake Caliper (Right Side)
        *9 Front Brake Caliper (Left Side) - -

      3. Each valve operates as shown below:

        Item Port TRC Not Activated TRC Activated
        Increase Mode Holding Mode Reduction Mode
        Master Cylinder Cut Solenoid Valve (1), (4) (A), (D) OFF (Open) ON* ON* ON*
        Reservoir Cut Solenoid Valve (2), (3) (B), (C) OFF (Closed) ON (Open) ON (Open) ON (Open)
        Front Brakes Pressure Holding Solenoid Valve (5), (8) (E), (H) OFF (Open) OFF (Open) ON (Closed) ON (Closed)
        Pressure Reduction Solenoid Valve (9), (12) (I), (L) OFF (Closed) OFF (Closed) OFF (Closed) ON (Open)
        Brake Wheel Cylinder Pressure - - - Increased Held Reduced
        Rear Brakes Pressure Holding Solenoid Valve (6), (7) (F), (G) OFF (Open) ON (Closed) ON (Closed) ON (Closed)
        Pressure Reduction Solenoid Valve (10), (11) (J), (K) OFF (Closed) ON (Open) ON (Open) ON (Open)
        Brake Wheel Cylinder Pressure - - - - - -
        Pump OFF ON ON ON

        *: Hydraulic pressure is controlled by continuously cycling the solenoid valves between open and closed, according to the operating conditions.

    5. VSC


      1. VSC, by way of solenoid valves, controls the fluid pressure generated by the pump and applies it to each wheel cylinder in the following 3 modes: pressure reduction, pressure holding, and pressure increase modes. As a result, understeer and oversteer tendencies are controlled.

        B00230RE04

      2. In understeer restraining control, the skid control ECU controls engine output and applies the brakes of the front and rear wheel on the inside of the turn. Also, depending on whether the brakes are applied and the vehicle condition, there are circumstances in which the brake of a specific wheel may not be applied even if it was targeted for braking. The diagram below shows the hydraulic circuit in pressure increase mode, as it restrains an understeer tendency while the vehicle is making a right turn. In other operating modes, the pressure holding valve and the pressure reduction valve are turned ON/OFF according to the ABS and EBD operation pattern.

        Figure 1. VSC Operation (Understeer Restraining Control)

        B00231XC04
        *1 Brake Master Cylinder Sub-assembly *2 Brake Actuator Assembly
        *3 Master Cylinder Pressure Sensor *4 Pump
        *5 Reservoir *6 Front Brake Caliper (Right Side)
        *7 Rear Brake Caliper (Left Side) *8 Rear Brake Caliper (Right Side)
        *9 Front Brake Caliper (Left Side) - -

      3. Each valve operates as shown below:

        Item Port VSC Not Activated VSC Activated
        Increase Mode Holding Mode Reduction Mode
        Master Cylinder Cut Solenoid Valve (1), (4) (A), (D) OFF (Open) ON* ON* ON*
        Reservoir Cut Solenoid Valve (2), (3) (B), (C) OFF (Closed) ON (Open) ON (Open) ON (Open)
        Front Brake Pressure Holding Solenoid Valve (5) (E) OFF (Open) OFF (Open) ON (Closed) ON (Closed)
        (8) (H) OFF (Open) ON (Closed) ON (Closed) ON (Closed)
        Pressure Reduction Solenoid Valve (9) (I) OFF (Closed) OFF (Closed) OFF (Closed) ON (Open)
        (12) (L) OFF (Closed) OFF (Closed) OFF (Closed) OFF (Closed)
        Brake Wheel Cylinder Pressure Right - - Increased Held Reduced
        Left - - Increased Held Reduced
        Rear Brake Pressure Holding Solenoid Valve (6) (F) OFF (Open) ON (Closed) ON (Closed) ON (Closed)
        (7) (G) OFF (Open) OFF (Open) ON (Closed) ON (Closed)
        Pressure Reduction Solenoid Valve (10) (J) OFF (Closed) OFF (Closed) OFF (Closed) OFF (Closed)
        (11) (K) OFF (Closed) OFF (Closed) OFF (Closed) ON (Open)
        Brake Wheel Cylinder Pressure Right - - Increased Held Reduced
        Left - - - - -
        Pump OFF ON ON ON

        *: Hydraulic pressure is controlled by continuously cycling the solenoid valves between open and closed, according to the operating conditions.

      4. In oversteer restraining control, the skid control ECU applies the brakes of the front and rear wheels on the outside of the turn. Also, depending on whether the brakes are applied and the vehicle condition, the brake of a specific wheel may not be applied even if it was targeted for braking. The diagram below shows the hydraulic circuit in pressure increase mode, as it restrains an oversteer tendency while the vehicle is making a right turn. In other operating modes, the pressure holding valve and the pressure reduction valve are turned ON/OFF according to the ABS and EBD operation patterns.

        Figure 2. VSC Operation (Oversteer Restraining Control)

        B00238HC02
        *1 Brake Master Cylinder Sub-assembly *2 Brake Actuator Assembly
        *3 Master Cylinder Pressure Sensor *4 Pump
        *5 Reservoir *6 Front Brake Caliper (Right Side)
        *7 Rear Brake Caliper (Left Side) *8 Rear Brake Caliper (Right Side)
        *9 Front Brake Caliper (Left Side) - -

      5. Each valve operates as shown below:

        Item Port VSC Not Activated VSC Activated
        Increase Mode Holding Mode Reduction Mode
        Master Cylinder Cut Solenoid Valve (1), (4) (A), (D) OFF (Open) ON* ON* ON*
        Reservoir Cut Solenoid Valve (2), (3) (B), (C) OFF (Closed) ON (Open) ON (Open) ON (Open)
        Front Brake Pressure Holding Solenoid Valve (5) (E) OFF (Open) ON (Closed) ON (Closed) ON (Closed)
        (8) (H) OFF (Open) OFF (Open) ON (Closed) ON (Closed)
        Pressure Reduction Solenoid Valve (9) (I) OFF (Closed) OFF (Closed) OFF (Closed) OFF (Closed)
        (12) (L) OFF (Closed) OFF (Closed) OFF (Closed) ON (Open)
        Brake Wheel Cylinder Pressure Right - - - - -
        Left - - Increased Held Reduced
        Rear Brake Pressure Holding Solenoid Valve (6) (F) OFF (Open) OFF (Open) ON (Closed) ON (Closed)
        (7) (G) OFF (Open) ON (Closed) ON (Closed) ON (Closed)
        Pressure Reduction Solenoid Valve (10) (J) OFF (Closed) OFF (Closed) OFF (Closed) ON (Open)
        (11) (K) OFF (Closed) OFF (Closed) OFF (Closed) OFF (Closed)
        Brake Wheel Cylinder Pressure Right - - - - -
        Left - - Increased Held Reduced
        Pump OFF ON ON ON

        *: Hydraulic pressure is controlled by continuously cycling the solenoid valves between open and closed, according to the operating conditions.

    6. Hill-start Assist Operation


      1. When hill-start assist control is operating, the skid control ECU holds the brake fluid pressure.

      2. Based on the information provided by various sensors, switches, and the ECM, the skid control ECU determines whether to activate hill-start assist control.

        B0023NCE01
        B00236BC01
        *1 Brake Master Cylinder Sub-assembly *2 Brake Actuator Assembly
        *3 Master Cylinder Pressure Sensor *4 Pump
        *5 Reservoir *6 Front Brake Caliper (Right Side)
        *7 Rear Brake Caliper (Left Side) *8 Rear Brake Caliper (Right Side)
        *9 Front Brake Caliper (Left Side) - -
        Item Port Not Activated Hill-start Assist Control Activated
        Holding Mode Reduction Mode
        Master Cylinder Cut Solenoid Valve (1), (4) (A), (D) OFF (Open) ON* ON*
        Reservoir Cut Solenoid Valve (2), (3) (B), (C) OFF (Closed) OFF (Closed) OFF (Closed)
        Front Brakes Pressure Holding Solenoid Valve (5), (8) (E), (H) OFF (Open) OFF (Open) OFF (Open)
        Pressure Reduction Solenoid Valve (9), (12) (I), (L) OFF (Closed) OFF (Closed) OFF (Closed)
        Brake Wheel Cylinder Pressure - - Hold Reduce
        Rear Brakes Pressure Holding Solenoid Valve (6), (7) (F), (G) OFF (Open) OFF (Open) OFF (Open)
        Pressure Reduction Solenoid Valve (10), (11) (J), (K) OFF (Closed) OFF (Closed) OFF (Closed)
        Brake Wheel Cylinder Pressure - - Hold Reduce
        Pump OFF OFF OFF

        *: Hydraulic pressure is controlled by continuously cycling the solenoid valves between open and closed, according to the operating conditions.

    7. Brake Hold


      1. The operation of the solenoid valves under the brake hold is the same as the operation of the hill-start assist control.

    8. VSC and Cooperative Control with EPS


      1. The operation of the solenoid valves under the steering cooperative control is the same as the TRC or VSC operation.