CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU) Audio Receiver Assembly Communication Stop Mode

DTC Code DTC Name
Audio Receiver Assembly Communication Stop Mode

DESCRIPTION

Detection Item

Symptom

Trouble Area

Audio Receiver Assembly Communication Stop Mode

Either condition is met:

  • Communication stop for "Display and Navigation (AVN)" is indicated on the "Communication Bus Check" screen of the GTS.

    Click here

  • Communication system DTCs (DTCs that start with U) that correspond to "Audio Receiver Assembly Communication Stop Mode" in "DTC Combination Table" are output.

    Click here

  • Radio and display receiver assembly branch line or connector

  • Power source circuit of radio and display receiver assembly

  • Radio and display receiver assembly ground circuit

  • Radio and display receiver assembly

WIRING DIAGRAM

C355794E03

CAUTION / NOTICE / HINT

Note:

  • Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

    Click here

  • Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

  • After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  • After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

    DTC check procedure: Turn the ignition switch to ON and wait at least 31 seconds.

  • After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

    Click hereClick here

  • Inspect the fuses for circuits related to this system before performing the following procedure.

Tip:

  • Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

  • When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.

PROCEDURE

  1. CHECK FOR OPEN IN CAN BUS LINES (RADIO AND DISPLAY RECEIVER ASSEMBLY BRANCH LINE)

    1. Disconnect the cable from the negative (-) battery terminal.

    2. Disconnect the E60 radio and display receiver assembly connector.

    3. C240580C17

      *a

      Front view of wire harness connector

      (to Radio and Display Receiver Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      E60-9 (CANH) - E60-10 (CANL)

      Cable disconnected from negative (-) battery terminal

      54 to 69 Ω

    Result

    Result

    Result

    OK

    NG
    NG

    REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY)

    OK

  2. CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

    1. Disconnect the E1 radio and display receiver assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      C240506C57

      *a

      Front view of wire harness connector

      (to Radio and Display Receiver Assembly)

      -

      -

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      E1-7 (GND1) - Body ground

      Cable disconnected from negative (-) battery terminal

      Below 1 Ω

    3. Reconnect the cable to the negative (-) battery terminal.

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection

      Condition

      Specified Condition

      E1-4 (+B1) - Body ground

      Always

      11 to 14 V

      E1-3 (ACC1) - Body ground

      Ignition switch ACC

      11 to 14 V

      E60-1 (IG) - Body ground

      Ignition switch ON

      11 to 14 V

    Result

    Result

    Proceed to

    OK

    A

    • NG (for GND1 or IG signal circuit)

    • NG (for +B1 or ACC1 signal circuit (w/o Stop and Start System))

    B

    NG (for +B1 or ACC1 signal circuit (w/ Stop and Start System))

    C
    A

    REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

    Click here

    B

    REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

    C

    GO TO STOP AND START SYSTEM (FOR BACKUP BOOST CONVERTER CIRCUIT)

    Click here