FRONT DOOR LOCK INSTALLATION

CAUTION / NOTICE / HINT

Tip:

  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE

  1. PRECAUTION

    Note:

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click hereClick here

  2. INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY

    1. B371397

      Install the front door inside locking cable assembly as shown in the illustration.

  3. INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY

    1. B371395

      Install the front door lock remote control cable assembly as shown in the illustration.

  4. INSTALL FRONT DOOR LOCK COVER SUB-ASSEMBLY

    1. Engage the 2 claws.

    2. B371392

      Engage the 2 claws to install the front door lock cover sub-assembly as shown in the illustration.

  5. INSTALL FRONT DOOR LOCK ASSEMBLY

    Note:

    • When reusing the removed front door lock assembly, replace the door lock wiring harness seal on the connector with a new one.

    • Do not allow grease or dust to adhere to the door lock wiring harness seal surface of the connector.

    • Reusing the door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water ingress. This may result in a malfunction of the front door lock assembly.

    1. Apply MP grease to the sliding parts of the front door lock assembly.

    2. When reusing the front door lock assembly:

      1. Install a new door lock wiring harness seal to the front door lock assembly.

    3. B371389C01

      *1

      Front Door Lock Open Rod

      Connect the front door lock open rod to the front door lock assembly.

      Tip:

      Make sure that the front door lock open rod is securely connected to the front door lock assembly.

    4. Using a T30 "TORX" socket wrench, install the front door lock assembly with the 3 screws.

      5.0 N*m

      51 kgf*cm

      44 in.*lbf

    5. Connect the connector.

  6. INSTALL FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (for Driver Side)

    Click hereClick here

  7. INSTALL FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (for Front Passenger Side)

    w/ Lock Cylinder

    Tip:

    Use the same procedure as for the driver side.

  8. INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY

    Click hereClick here

  9. INSTALL FRONT DOOR GLASS RUN

    Click hereClick here

  10. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY (w/o Power Window)

    Click hereClick here

  11. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY (w/ Power Window)

    Click hereClick here

  12. INSTALL FRONT DOOR SERVICE HOLE COVER

    Click hereClick here

  13. INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP ASSEMBLY

    Click hereClick here

  14. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY

    Click hereClick here

  15. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH (w/o Mirror Heater)

    Click hereClick here

  16. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH (w/ Mirror Heater)

    Click hereClick here

  17. INSTALL FRONT DOOR TRIM COVER

    Click hereClick here

  18. INSTALL FRONT DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)

    Click hereClick here

  19. INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Driver Side with Power Window)

    Click hereClick here

  20. INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Front Passenger Side with Power Window)

    Click hereClick here

  21. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click hereClick hereClick here

  22. INSPECT POWER WINDOW OPERATION (w/ Power Window)

    Click here