POWER WINDOW CONTROL SYSTEM Front Passenger Side Power Window Auto Up / Down Function does not Operate with Front Passenger Side Power Window Switch

DESCRIPTION

If the manual up and down function operates normally but the auto up and down function does not, then fail-safe mode may be functioning.

If power window initialization has not been performed, the auto up and down function will not operate.

Click here

WIRING DIAGRAM


  1. for LHD:

    B006GCZE07

  2. for RHD:

    B006GCZE08

CAUTION / NOTICE / HINT

Note


  • If the front power window regulator motor assembly RH (for LHD) or front power window regulator motor assembly LH (for RHD) has been replaced with a new one, initialize the power window control system.

    Click here

  • Check that the "P Window Auto Up" and "P Window Auto Down" power window control system customize settings are "ON" before proceeding with work.

    Click here

  • After the catch protection function operates, the auto operation is not performed the first time auto up is performed. All auto up operations performed after the first operate normally.

Tech Tips

If the pulse sensor built into the front power window regulator motor assembly RH is malfunctioning, the power window control system enters fail-safe mode. The remote up and down and auto up and down functions cannot be operated during fail-safe mode. However, the power window can be closed by holding the power window regulator switch assembly at the auto up position, and opened manually by pushing down the power window regulator switch assembly.

Click here

PROCEDURE


  1. READ VALUE USING GTS (P-DOOR MOTOR)


    1. Using the GTS, read the data for the condition when the power window regulator switch assembly was operated.

      Click here


      Body Electrical > P-Door Motor > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      P Door P/W Auto SW Front passenger door power window auto switch signal OFF or ON

      OFF: Front passenger door power window auto switch not being operated

      ON: Front passenger door power window auto switch being operated

      		 -

      Body Electrical > P-Door Motor > Data List
      Tester Display
      P Door P/W Auto SW
      OK
      On the GTS screen, ON or OFF is displayed accordingly.
      Result
      Result Proceed to
      OK (for RHD) A
      OK (for LHD) B
      NG C

    B

    PERFORM INITIALIZATION Click here

    C

    INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY Click here

    A

  2. PERFORM INITIALIZATION


    1. Initialize the front power window regulator motor assembly RH.

      Click here

      OK
      Power window system operates normally.
      Result
      Proceed to
      OK
      NG

    OK

    END (PROBLEM DUE TO INITIALIZATION FAILURE)

    NG

    REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH Click here

  3. PERFORM INITIALIZATION


    1. Initialize the front power window regulator motor assembly LH.

      Click here

      OK
      Power window system operates normally.
      Result
      Proceed to
      OK
      NG

    OK

    END (PROBLEM DUE TO INITIALIZATION FAILURE)

    NG

    REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH Click here

  4. INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY


    1. Remove the power window regulator switch assembly.

      Click here

    2. Inspect the power window regulator switch assembly.

      Click here

      Result
      Result Proceed to
      OK (for LHD) A
      OK (for RHD) B
      NG C

    B

    CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH) Click here

    C

    REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY Click here

    A

  5. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)


    1. Disconnect the I1 power window regulator switch assembly connector.

    2. Disconnect the H2 front power window regulator motor assembly RH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      I1-4 (AUTO) - H2-4 (AUTO) Always Below 1 Ω
      I1-4 (AUTO) or H2-4 (AUTO) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  6. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)


    1. Disconnect the I4 power window regulator switch assembly connector.

    2. Disconnect the H21 front power window regulator motor assembly LH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      I1-4 (AUTO) - H21-4 (AUTO) Always Below 1 Ω
      I1-4 (AUTO) or H21-4 (AUTO) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR