ECD SYSTEM(for Swirl Control Valve), Diagnostic DTC:P0402

DTC Code DTC Name
P0402 Exhaust Gas Recirculation "A" Flow Excessive Detected

DESCRIPTION

Refer to DTC P0401 (Click here).

Tip:

For more information on the EGR control, refer to System Description (Click here).

DTC No.

DTC Detection Condition

Trouble Area

P0402

During normal operation, EGR positive deviation exceeds limit value, or EGR rate exceeds limit value for 5 seconds.

(1 trip detection logic)

  • Intake system air leak

  • Air cleaner element assembly

  • Diesel throttle body assembly

  • Mass air flow meter

  • EGR valve assembly

  • Turbocharger sub-assembly

  • Swirl Control Valve

  • ECM

CAUTION / NOTICE / HINT

Note:

  • When replacing the ECM, the ECM needs Registration and Initialization (Click here).

  • After replacing the EGR valve assembly, the ECM needs initialization (Click here).

  • After replacing the mass air flow meter, the ECM needs initialization (Click here).

  • After replacing the swirl control valve, the ECM needs initialization (Click here).

Tip:

  • When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

  • Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

PROCEDURE

  1. CHECK INTAKE SYSTEM

    1. Check for air leaks in the intake system from the mass air flow meter to the turbocharger sub-assembly.

    REPAIR OR REPLACE INTAKE SYSTEMClick here

  2. CHECK AIR CLEANER ELEMENT ASSEMBLY

    1. Inspect the air cleaner element assembly.

      OK

      No blockage in air cleaner element assembly.

    REPLACE AIR CLEANER ELEMENT ASSEMBLYClick here

  3. CHECK MASS AIR FLOW METER

    1. Check for DTCs related to the mass air flow meter.

      OK

      DTCs related to the mass air flow meter are not output.

    REPAIR OR REPLACE MASS AIR FLOW METERClick here

  4. CHECK SWIRL CONTROL VALVE

    1. Check that the swirl control valve is not stuck closed or blocked.

      OK

      Swirl control valve is moving correctly and not stuck closed or blocked.

    REPLACE SWIRL CONTROL VALVEClick here

  5. CHECK DIESEL THROTTLE BODY ASSEMBLY

    1. Check for DTCs related to the diesel throttle body assembly.

      OK

      DTCs related to the diesel throttle body assembly are not output.

    REPAIR OR REPLACE DIESEL THROTTLE BODY ASSEMBLYClick here

  6. CHECK EGR VALVE ASSEMBLY

    1. Check for DTCs related to the EGR valve assembly.

      OK

      DTCs related to the EGR valve assembly are not output.

    REPAIR OR REPLACE EGR VALVE ASSEMBLYClick here

  7. CHECK TURBOCHARGER SUB-ASSEMBLY

    1. Check for DTCs related to the turbocharger sub-assembly.

      OK

      DTCs related to the turbocharger sub-assembly are not output.

    REPAIR OR REPLACE TURBOCHARGER SUB-ASSEMBLYClick here

  8. CHECK WHETHER DTC OUTPUT RECURS (DTC P0402)

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Clear the DTCs (Click here).

    4. Turn the ignition switch off and wait for 60 seconds or more [A].

    5. Perform road test [B].

    6. Repeat [A] and [B] for the number of trips detected.

    7. Enter the following menus: Engine and ECT / Trouble Codes.

    8. Read the DTCs.

      Table 1. Result

      Result

      Proceed to

      No DTC output

      A

      DTC P0402

      B

    END

    REPLACE ECMClick here

  9. REPAIR OR REPLACE INTAKE SYSTEM

    1. Repair or replace the malfunctioning parts of the intake system.

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIREDClick here

  10. REPLACE AIR CLEANER ELEMENT ASSEMBLY

    1. Replace the air cleaner element assembly.

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIREDClick here

  11. REPAIR OR REPLACE MASS AIR FLOW METER

    1. Repair or replace mass air flow meter or perform inspections and troubleshooting for related DTCs (Click hereClick here).

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIREDClick here

  12. REPLACE SWIRL CONTROL VALVE

    1. Replace the swirl control valve (Click here).

    2. Perform the swirl valve learning value reset (Click here).

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIREDClick here

  13. REPAIR OR REPLACE DIESEL THROTTLE BODY ASSEMBLY

    1. Repair or replace diesel throttle body assembly or perform inspections and troubleshooting for related DTCs (Click hereClick here).

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIREDClick here

  14. REPAIR OR REPLACE EGR VALVE ASSEMBLY

    1. Repair or replace EGR valve assembly or perform inspections and troubleshooting for related DTCs (Click hereClick here).

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIREDClick here

  15. REPAIR OR REPLACE TURBOCHARGER SUB-ASSEMBLY

    1. Repair or replace turbocharger sub-assembly or perform inspections and troubleshooting for related DTCs (Click hereClick here).

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIREDClick here

  16. REPLACE ECM

    1. Replace the ECM (Click here).

  17. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Clear the DTCs (Click here).

    4. Turn the ignition switch off and wait for 60 seconds or more [A].

    5. Perform road test [B].

    6. Repeat [A] and [B] for the number of trips detected.

    7. Enter the following menus: Engine and ECT / Trouble Codes.

    8. Confirm that the DTC is not output again.

    END