WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Entry and Start System) SYSTEM DESCRIPTION

  1. WIRELESS DOOR LOCK CONTROL SYSTEM

    The wireless door lock control system can be used to lock and unlock all doors from a distance. The system is controlled by a door control transmitter assembly which sends radio waves to the door control receiver. The main body ECU (multiplex network body ECU) performs an ID code identification process and operates the door lock control.

  2. FUNCTION OF MAIN COMPONENTS

    Component

    Function

    Door control transmitter assembly

    • Has the lock, unlock and back door open switches.

    • Transmits weak radio waves (recognition codes and function codes) to the door control receiver.

    Door control receiver

    Receives weak radio waves from the door control transmitter assembly and sends them to the main body ECU (multiplex network body ECU).

    • Door courtesy light switch assembly

    • Back door courtesy light switch

    • Turns on when a door is opened and turns off when it is closed.

    • Outputs door status signals (open or closed) to the main body ECU (multiplex network body ECU).

    Unlock warning switch assembly

    Detects if the key is inserted in the ignition key cylinder or not.

    Front door lock assembly

    Rear door lock assembly

    • The built-in motor locks or unlocks the door.

    • Transmits the door lock position of each door to the main body ECU (multiplex network body ECU).

    Main body ECU (multiplex network body ECU)

    Sends wireless door lock control signals in response to the code data from the door control receiver and signals from each switch.

  3. SYSTEM FUNCTION

    The door control transmitter assembly has the lock, unlock and back door open switches. Operating these switches activates each function.

    The wireless door lock control system has the following functions:

    Tip:

    The default settings of the following functions are on. Part of these functions can be customized.

    Click here

    Function

    Operation

    All door lock

    Pressing the lock switch locks all doors.

    Back door open

    Pressing the back door open switch of the door control transmitter assembly for longer than about 0.8 seconds opens the back door.

    Automatic lock

    If none of the doors is opened within 30 seconds after they are unlocked by wireless door lock control, all doors will lock again automatically.

    Answer back (Hazard warning light)

    • When the doors are locked by wireless operation, the hazard warning lights flash once.

    • When the doors are unlocked by wireless operation, the hazard warning lights flash twice.

    Illuminated entry

    When all doors are locked, pressing the unlock switch causes the interior lights to come on simultaneously with the unlock operation.

    Self-diagnostic mode

    If the door control receiver receives normal radio waves from the door control transmitter assembly when the system is in diagnostic mode, it flashes the interior lights in a normal pattern that corresponds to the function of each switch.

    Transmitter recognition code registration

    Enables registration (writing and storing) of door control transmitter assembly recognition codes in the EEPROM that is contained in the door control receiver.

  4. TRANSMITTER RECOGNITION CODE REGISTRATION FUNCTION

    The table below shows the 4 ID registration function modes. The codes are electronically registered (written and stored) in the EEPROM that is contained in the door control receiver.

    Mode

    Function

    Add mode

    Adds a newly received code while preserving any previously registered codes.

    This mode is used when adding a new door control transmitter assembly. If the maximum registration number is exceeded, the oldest one is cleared first.

    Rewrite mode

    Clears all previously registered codes and registers only newly input codes.

    Confirmation mode

    Confirms how many codes are currently registered. When adding a new code, this mode is used to check how many codes already exist.

    Prohibition mode

    Deletes all registered codes and disables the wireless door lock function.

    This mode is used when the door control transmitter assembly is lost.

  5. CONDITIONS THAT WIRELESS FUNCTIONS DO NOT OPERATE

    1. The lock function will not operate when either of the following conditions is met:

      • Any of the doors is open.

      • The key is inserted in the ignition key cylinder.

    2. The unlock function will not operate when the following condition is met:

      • The key is inserted in the ignition key cylinder.