CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU) Main Body ECU Communication Stop Mode

DTC Code DTC Name
Main Body ECU Communication Stop Mode

DESCRIPTION

Detection Item

Symptom

Trouble Area

Main Body ECU Communication Stop Mode

Either condition is met:

  • Communication stop for "Main Body" is indicated on the "Communication Bus Check" screen of the GTS.

    Click here

  • Communication system DTCs (DTCs that start with U) that correspond to "Main Body ECU Communication Stop Mode" in "DTC Combination Table" are output.

    Click here

  • Main body ECU (multiplex network body ECU) branch line or connector

  • Power source circuit of main body ECU (multiplex network body ECU) or instrument panel junction block assembly

  • Main body ECU (multiplex network body ECU) or instrument panel junction block assembly ground circuit

  • Main body ECU (multiplex network body ECU) or instrument panel junction block assembly

WIRING DIAGRAM

C355786E02

CAUTION / NOTICE / HINT

Note:

  • Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

    Click here

  • Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

  • After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  • After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

    DTC check procedure: Turn the ignition switch to ON and wait at least 20 seconds.

  • After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

    Click hereClick here

  • Inspect the fuses for circuits related to this system before performing the following procedure.

Tip:

  • Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

  • When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.

PROCEDURE

  1. CHECK FOR OPEN IN CAN BUS LINES (MULTIPLEX NETWORK BODY ECU) BRANCH LINE)

    1. Disconnect the cable from the negative (-) battery terminal.

    2. Disconnect the E22 main body ECU (multiplex network body ECU) connector.

    3. C206279C63

      *a

      Front view of wire harness connector

      (to Main Body ECU (Multiplex Network Body ECU))

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      E22-14 (CANH) - E22-13 (CANL)

      Cable disconnected from negative (-) battery terminal

      54 to 69 Ω

    Result

    Result

    Result

    OK

    NG
    NG

    REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

    OK

  2. CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

    1. Disconnect the 3A and 3C instrument panel junction block assembly connectors.

    2. C277515C03

      *a

      Front view of wire harness connector

      (to Instrument Panel Junction Block Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      3C-9 (GND1) - Body ground

      Cable disconnected from negative (-) battery terminal

      Below 1 Ω

    3. Reconnect the cable to the negative (-) battery terminal.

    4. C272557C20

      *a

      Front view of wire harness connector

      (to Instrument Panel Junction Block Assembly)

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection

      Condition

      Specified Condition

      3A-43 (BECU) - Body ground

      Always

      11 to 14 V

    Result

    Result

    Result

    OK

    NG
    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

    OK

  3. INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG1 NO. 3 RELAY AND ACC RELAY)

    1. Inspect the IG1 No. 3 relay and ACC relay of the instrument panel junction block assembly.

      Tip:

      If the IG signal circuit and ACC signal circuit have no problem, replace the main body ECU (multiplex network body ECU).

    Result

    Result

    Result

    OK

    NG
    OK

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

    NG

    REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY