ENGINE ASSEMBLY COMPONENTS
ILLUSTRATION
| *1 | AIR CLEANER CAP SUB-ASSEMBLY WITH NO. 1 AIR CLEANER HOSE | *2 | AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY |
| *3 | AIR CLEANER CASE SUB-ASSEMBLY | *4 | HOOD SUB-ASSEMBLY |
| *5 | VACUUM HOSE | *6 | NO. 2 PCV HOSE |
| *7 | WASHER NOZZLE HOSE | - | - |
 |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *A | for 4WD | - | - |
| *1 | FRONT FENDER SEAL LH | *2 | FRONT FENDER SEAL RH |
| *3 | FRONT UPPER FENDER APRON SEAL LH | *4 | FRONT UPPER FENDER APRON SEAL RH |
| *5 | NO. 1 ENGINE UNDER COVER ASSEMBLY | *6 | NO. 1 RADIATOR AIR GUIDE |
| *7 | NO. 2 ENGINE UNDER COVER | *8 | NO. 3 ENGINE UNDER COVER SUB-ASSEMBLY |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | FAN SHROUD | *2 | NO. 1 OIL COOLER INLET HOSE |
| *3 | NO. 1 OIL COOLER OUTLET HOSE | *4 | RADIATOR ASSEMBLY |
| *5 | RADIATOR HOSE INLET | *6 | RADIATOR HOSE OUTLET |
| *7 | RADIATOR RESERVOIR | *8 | OIL RESERVOIR |
| *9 | FAN PULLEY | *10 | FLUID COUPLING FAN |
| *11 | WIRE HARNESS | *12 | GROMMET |
| *13 | CLAMP | *14 | FAN AND GENERATOR V BELT |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *A | w/ Cover | - | - |
| *1 | ECM | *2 | GLOVE COMPARTMENT DOOR ASSEMBLY |
| *3 | NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY | *4 | INSTRUMENT PANEL WIRE |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *1 | ENGINE WIRE | *2 | INTAKE AIR SURGE TANK |
| *3 | NO. 1 SURGE TANK STAY | *4 | NO. 2 SURGE TANK STAY |
| *5 | THROTTLE BODY BRACKET | *6 | NO. 1 PCV HOSE |
| *7 | NO. 1 FUEL VAPOR FEED HOSE | *8 | NO. 4 WATER BY-PASS HOSE |
| *9 | NO. 5 WATER BY-PASS HOSE | *10 | OIL BAFFLE PLATE |
| *11 | GASKET | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
 |
Do not apply lubricants to the threads parts | - | - |
ILLUSTRATION
| *1 | EXHAUST MANIFOLD SUB-ASSEMBLY LH | *2 | EXHAUST MANIFOLD SUB-ASSEMBLY RH |
| *3 | FLYWHEEL HOUSING SIDE COVER | *4 | FRONT EXHAUST PIPE ASSEMBLY |
| *5 | FRONT NO. 2 EXHAUST PIPE ASSEMBLY | *6 | MANIFOLD STAY |
| *7 | NO. 2 MANIFOLD STAY | *8 | STARTER ASSEMBLY |
| *9 | NO. 1 EXHAUST PIPE SUPPORT | *10 | COMPRESSION SPRING |
| *11 | GASKET | *12 | STARTER WIRE |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | COOLER COMPRESSOR ASSEMBLY | *2 | ENGINE WIRE |
| *3 | GENERATOR ASSEMBLY | *4 | NO. 1 FUEL PIPE SUB-ASSEMBLY |
| *5 | NO. 2 FUEL PIPE SUB-ASSEMBLY | *6 | VANE PUMP ASSEMBLY |
| *7 | WATER HOSE SUB-ASSEMBLY | *8 | BATTERY POSITIVE TERMINAL |
| *9 | NO. 1 RELAY BLOCK COVER SIDE | *10 | NO. 1 RELAY BLOCK COVER UPPER |
| *11 | WIRE HARNESS CLAMP BRACKET | *12 | NO. 2 ENGINE WIRE |
| *13 | BATTERY HOLD DOWN CLAMP | *14 | BATTERY |
| *15 | BATTERY INSULATOR | *16 | BATTERY TRAY |
| *17 | TERMINAL CAP | *18 | WIRE HARNESS |
| *19 | GENERATOR BRACKET | *20 | ENGINE ROOM RELAY BLOCK |
 |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
ILLUSTRATION
| *A | for 4WD | - | - |
| *1 | FRONT AXLE HUB GREASE CAP | *2 | FRONT AXLE SHAFT NUT |
| *3 | FRONT DRIVE SHAFT ASSEMBLY LH | *4 | FRONT DRIVE SHAFT HOLE SNAP RING |
| *5 | FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH | *6 | FRONT SPEED SENSOR LH |
| *7 | TIE ROD END SUB-ASSEMBLY LH | *8 | LOCK CAP |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
| ● | Non-reusable part |  |
Differential oil |
 |
MP grease | |
Do not apply lubricants to the threaded parts |
ILLUSTRATION
| *A | for 4WD | - | - |
| *1 | POWER STEERING LINK ASSEMBLY | *2 | STEERING SLIDING YOKE |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | - | - |
ILLUSTRATION
| *A | for 4WD | - | - |
| *1 | FRONT DIFFERENTIAL CARRIER ASSEMBLY | *2 | FRONT DIFFERENTIAL BREATHER HOSE |
| *3 | FRONT NO. 1 DIFFERENTIAL SUPPORT | *4 | FRONT NO. 2 DIFFERENTIAL SUPPORT |
| *5 | FRONT NO. 3 DIFFERENTIAL SUPPORT | *6 | DIFFERENTIAL MOUNT NUT |
| *7 | UPPER DIFFERENTIAL MOUNT STOPPER | *8 | LOWER DIFFERENTIAL MOUNT STOPPER |
| *9 | DIFFERENTIAL BREATHER TUBE BRACKET | *10 | DIFFERENTIAL MOTOR ACTUATOR CONNECTOR |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
| |
Do not apply lubricants | - | - |
ILLUSTRATION
| *A | for 2WD | - | - |
| *1 | PROPELLER SHAFT GUARD | *2 | PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
| |
Do not apply lubricants | - | - |
ILLUSTRATION
| *A | for 4WD | - | - |
| *1 | FRONT PROPELLER SHAFT ASSEMBLY | *2 | PROPELLER SHAFT GUARD |
| *3 | PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY | - | - |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
| |
Do not apply lubricants | - | - |
ILLUSTRATION
| *A | for 2WD | - | - |
| *1 | AUTOMATIC TRANSMISSION ASSEMBLY | *2 | DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT |
| *3 | GROUND WIRE | *4 | NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY |
| *5 | OIL COOLER TUBE | *6 | REAR ENGINE MOUNTING INSULATOR |
| *7 | STIFFENER PLATE LH | *8 | STIFFENER PLATE RH |
| *9 | TRANSMISSION CONTROL CABLE ASSEMBLY | *10 | TRANSMISSION INSULATOR RH |
| *11 | WIRE HARNESS | *12 | NO. 4 CYLINDER BLOCK INSULATOR |
| *13 | NO. 2 END PLATE | *14 | OIL COOLER TUBE CLAMP |
| *a | BLACK: x 1 SILVER: x 5 |
- | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | * | For use with union nut wrench |
| ● | Non-reusable part | |
Clutch spline grease |
ILLUSTRATION
| *A | for 4WD | - | - |
| *1 | AUTOMATIC TRANSMISSION ASSEMBLY | *2 | DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT |
| *3 | GROUND WIRE | *4 | NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY |
| *5 | OIL COOLER TUBE | *6 | REAR ENGINE MOUNTING INSULATOR |
| *7 | STIFFENER PLATE LH | *8 | STIFFENER PLATE RH |
| *9 | TRANSMISSION CONTROL CABLE ASSEMBLY | *10 | TRANSMISSION INSULATOR RH |
| *11 | WIRE HARNESS | *12 | NO. 4 CYLINDER BLOCK INSULATOR |
| *13 | NO. 2 END PLATE | *14 | OIL COOLER TUBE CLAMP |
| *a | BLACK: x 1 SILVER: x 5 |
- | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | * | For use with union nut wrench |
| ● | Non-reusable part | |
Clutch spline grease |
ILLUSTRATION
| *1 | DRIVE PLATE AND RING GEAR SUB-ASSEMBLY | *2 | NO. 1 ENGINE HANGER |
| *3 | NO. 2 ENGINE HANGER | *4 | FRONT DRIVE PLATE SPACER |
| *5 | REAR DRIVE PLATE SPACER | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| ★ | Precoated part | - | - |