CYLINDER HEAD INSPECTION

PROCEDURE

  1. INSPECT CYLINDER HEAD SUB-ASSEMBLY FOR WARPAGE

    1. A352693C01

      *a

      Bottom Side

      *b

      Intake Manifold Side

      *c

      Turbocharger Sub-assembly Side

      Using a precision straightedge and feeler gauge, check the surfaces which contact the cylinder block sub-assembly, turbocharger sub-assembly and intake manifold for warpage.

      Maximum Warpage

      Item

      Specified Condition

      Bottom side

      0.05 mm (0.00197 in.)

      Intake manifold side

      0.10 mm (0.00394 in.)

      Turbocharger sub-assembly side

      0.05 mm (0.00197 in.)
      Tip:

      If the warpage is more than the maximum, replace the cylinder head sub-assembly.

  2. INSPECT CYLINDER HEAD SUB-ASSEMBLY FOR CRACKS

    1. A352694

      Using a dye penetrant, check the intake ports, exhaust ports and bottom surface of the cylinder head sub-assembly for cracks.

      Tip:

      If cracks are found, replace the cylinder head sub-assembly.

  3. INSPECT INTAKE VALVE

    1. A352695C01

      *a

      Overall Length

      Using a vernier caliper, measure the overall length of the intake valve.

      Standard Overall Length

      103.35 mm (4.07 in.)

      Minimum Overall Length

      103.10 mm (4.06 in.)

      Tip:

      If the overall length is less than the minimum, replace the intake valve.

    2. A352696

      Using a micrometer, measure the diameter of the valve stem.

      Standard Valve Stem Diameter

      5.470 to 5.485 mm (0.215 to 0.216 in.)

      Tip:

      If the valve stem diameter is not as specified, check the intake valve guide bush oil clearance.

      Click here

    3. A352697C01

      *a

      Margin Thickness

      Using a vernier caliper, measure the valve head margin thickness.

      Standard Margin Thickness

      1.0 mm (0.0394 in.)

      Minimum Margin Thickness

      0.5 mm (0.0197 in.)

      Tip:

      If the margin thickness is less than the minimum, replace the intake valve.

  4. INSPECT EXHAUST VALVE

    1. A352699C01

      *a

      Overall Length

      Using a vernier caliper, measure the overall length of the exhaust valve.

      Standard Overall Length

      104.50 mm (4.11 in.)

      Minimum Overall Length

      104.25 mm (4.10 in.)

      Tip:

      If the overall length is less than the minimum, replace the exhaust valve.

    2. A352700

      Using a micrometer, measure the diameter of the valve stem.

      Standard Valve Stem Diameter

      5.465 to 5.480 mm (0.215 to 0.216 in.)

      Tip:

      If the valve stem diameter is not as specified, check the exhaust valve guide bush oil clearance.

      Click here

    3. A352701C01

      *a

      Margin Thickness

      Using a vernier caliper, measure the valve head margin thickness.

      Standard Margin Thickness

      1.2 mm (0.0472 in.)

      Minimum Margin Thickness

      0.7 mm (0.0276 in.)

      Tip:

      If the margin thickness is less than the minimum, replace the exhaust valve.

  5. INSPECT INNER COMPRESSION SPRING

    1. A352702

      Using a vernier caliper, measure the free length of the inner compression spring.

      Standard Free Length

      Item

      Specified Condition

      Intake

      55.95 mm (2.20 in.)

      Exhaust

      59.67 mm (2.35 in.)
    2. A352703C01

      *a

      Steel Square

      *b

      Intake Side: 39.35 mm (1.55 in.)

      Exhaust Side: 42.57 mm (1.68 in.)

      Using a steel square, measure the deviation of the inner compression spring.

      Maximum Angle (Reference)

      2°

      Tip:

      If the angle is more than the maximum, replace the inner compression spring.

  6. INSPECT VALVE GUIDE BUSH OIL CLEARANCE

    1. A352704

      Using a caliper gauge, measure the inside diameter of the valve guide bush.

      Standard Valve Guide Bush Inside Diameter

      5.510 to 5.530 mm (0.217 to 0.218 in.)

    2. Subtract the valve stem diameter measurement from the valve guide bush inside diameter measurement.

      Standard Oil Clearance

      Item

      Specified Condition

      Intake

      0.025 to 0.060 mm (0.000984 to 0.00236 in.)

      Exhaust

      0.030 to 0.065 mm (0.00118 to 0.00256 in.)

      Maximum Oil Clearance

      Item

      Specified Condition

      Intake

      0.080 mm (0.00315 in.)

      Exhaust

      0.085 mm (0.00335 in.)
      Tip:

      • Oil clearance = Inside diameter - Valve stem diameter

      • If the oil clearance is more than the maximum, replace the valve and valve guide bush.

  7. INSPECT VALVE SEATS

    1. Apply a light coat of Prussian blue to the valve face.

    2. A352705C01

      *a

      Width

      Lightly press the valve face against the valve seat.

      Note:

      Do not rotate the valve while pressing it.

    3. Check the valve face and valve seat by using the following procedure:

      1. If Prussian blue appears 360° around the entire valve face, the valve face is concentric.

        Tip:

        If the valve face is not concentric, replace the valve.

      2. If Prussian blue appears 360° around the entire valve seat, the valve seat and valve face are concentric.

        Tip:

        If the valve face is not concentric, resurface the valve seat.

        Click here

      3. Measure the width of the contact area of the valve seat and valve face.

        Standard Width

        Item

        Specified Condition

        Intake

        1.0 to 1.4 mm (0.0394 to 0.0551 in.)

        Exhaust

        1.0 to 1.4 mm (0.0394 to 0.0551 in.)