SLIDING ROOF SYSTEM DATA LIST / ACTIVE TEST
DATA LIST
Tip:Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Note:In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Sliding Roof / Data List.
According to the display on the intelligent tester, read the Data List.
Body Electrical > Sliding Roof > Data List
Tester Display
Type
Range
Normal Condition
Diagnostic Note
Open Switch
Slide open switch signal
ON or OFF
ON: Slide open switch pressed
OFF: Slide open switch not pressed
-
Close Switch
Slide close switch signal
ON or OFF
ON: Slide close switch pressed
OFF: Slide close switch not pressed
-
Up Switch
Tilt up switch signal
ON or OFF
ON: Tilt up switch pressed
OFF: Tilt up switch not pressed
-
Down Switch
Tilt down switch signal
ON or OFF
ON: Tilt down switch pressed
OFF: Tilt down switch not pressed
-
Hall IC1 Pulse
Hall IC1 pulse output
Lo or Hi
Lo and Hi repeat during motor operation
Lo: Hall IC1 output is low.
Hi: Hall IC1 output is high.
Hall IC1 Status
Status of Hall IC1
Normal or Error
Normal: Hall IC1 normal
Error: Hall IC1 not normal
-
Hall IC2 Pulse
Hall IC2 pulse output
Lo or Hi
Lo and Hi repeat during motor operation
Lo: Hall IC2 output is low.
Hi: Hall IC2 output is high.
Hall IC2 Status
Status of Hall IC2
Normal or Error
Normal: Hall IC2 normal
Error: Hall IC2 not normal
-
Ignition (Direct Signal)
Engine switch signal
ON or OFF
ON: Engine switch on (IG)
OFF: Engine switch off
-
Ignition (MPX)
Engine switch signal (LIN signal)
ON or OFF
ON: Engine switch on (IG)
OFF: Engine switch off
-
Door Courtesy
Driver side door courtesy light switch signal
ON or OFF
ON: Driver side door open
OFF: Driver side door closed
-
Door Key Close Operation
Key-linked sliding roof close signal
ON or OFF
ON: Driver side door key cylinder turned to lock position using key
OFF: Driver side door key cylinder not turned
Customize function.
Door Key Open Operation
Key-linked sliding roof open signal
ON or OFF
ON: Driver side door key cylinder turned to unlock position using key
OFF: Driver side door key cylinder not turned
Customize function.
Wireless Close Operation
Wireless sliding roof close signal
ON or OFF
ON: Transmitter LOCK switch pressed and held
OFF: Transmitter LOCK switch not pressed
Customize function.
Wireless Open Operation
Wireless sliding roof open signal
ON or OFF
ON: Transmitter UNLOCK switch pressed and held
OFF: Transmitter UNLOCK switch not pressed
Customize function.
Key Off Permission
Key-off operation permit signal
ON or OFF
ON: Driver side door not closed within 43 seconds after engine switch turned off
OFF: Any status except "ON" status
-
Door Key Related (Open)
Key-linked sliding roof open operation status
Avail or Not Avl
Avail: Key-linked sliding roof open operation available
Not Avl: Key-linked sliding roof open operation not available
Customize function.
Door Key Related (Close)
Key-linked sliding roof close operation status
Avail or Not Avl
Avail: Key-linked sliding roof close operation available
Not Avl: Key-linked sliding roof close operation not available
Customize function.
Wireless Key Rel (Open)
Wireless transmitter-linked sliding roof open operation status
Avail or Not Avl
Avail: Wireless transmitter-linked sliding roof open operation available
Not Avl: Wireless transmitter-linked sliding roof open operation not available
Customize function.
Wireless Key Rel (Close)
Wireless transmitter-linked sliding roof close operation status
Avail or Not Avl
Avail: Wireless transmitter-linked sliding roof close operation available
Not Avl: Wireless transmitter-linked sliding roof close operation not available
Customize function.
Door Key Related Operation
Direction for key-linked operation
Tilt or Slide
Tilt: Key-linked sliding roof operation tilts sliding roof
Slide: Key-linked sliding roof operation slides sliding roof
Customize function.
Wireless Key Rel Operation
Direction for wireless transmitter-linked operation
Tilt or Slide
Tilt: Wireless transmitter-linked sliding roof operation tilts sliding roof
Slide: Wireless transmitter-linked sliding roof operation slides sliding roof
Customize function.
Open Switch Failure(Past)
Slide open switch failure signal (Past)
ON or OFF
ON: Slide open switch signal failure (Past)
OFF: No slide open switch signal failure (Past)
-
Close Switch Failure(Past)
Slide close switch failure signal (Past)
ON or OFF
ON: Slide close switch signal failure (Past)
OFF: No slide close switch signal failure (Past)
-
Up Switch Failure(Past)
Tilt up switch failure signal (Past)
ON or OFF
ON: Tilt up switch signal failure (Past)
OFF: No tilt up switch signal failure (Past)
-
Down Switch Failure(Past)
Tilt down switch failure signal (Past)
ON or OFF
ON: Tilt down switch signal failure (Past)
OFF: No tilt down switch signal failure (Past)
-
Open Switch Failure(Current)
Slide open switch failure signal (Current)
ON or OFF
ON: Slide open switch signal failure (Current)
OFF: No slide open switch signal failure (Current)
-
Close Switch Failure(Current)
Slide close switch failure signal (Current) / ON or OFF
ON or OFF
ON: Slide close switch signal failure (Current)
OFF: No slide close switch signal failure (Current)
-
Up Switch Failure(Current)
Tilt up switch failure signal (Current)
ON or OFF
ON: Tilt up switch signal failure (Current)
OFF: No tilt up switch signal failure (Current)
-
Down Switch Failure(Current)
Tilt down switch failure signal (Current)
ON or OFF
ON: Tilt down switch signal failure (Current)
OFF: No tilt down switch signal failure (Current)
-
Number of Trouble Codes
Number of trouble codes
Min.: 0, Max.: 255
Number of DTCs displayed
-
ACTIVE TEST
Tip:Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Sliding Roof / Active Test.
According to the display on the intelligent tester, perform the Active Test.
Body Electrical > Sliding Roof > Active Test
Tester Display
Measurement Item
Control Range
Diagnostic Note
Slide Roof
Operate sliding roof
Opn/Dwn: Sliding roof slide open or tilt down operation occurs
Clos/Up: Sliding roof slide close or tilt up operation occurs
OFF: Sliding roof not operating
-