SPIRAL CABLE INSTALLATION

PROCEDURE


  1. INSTALL SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY

    Note


    • Do not replace the spiral with sensor cable sub-assembly with the battery connected and the engine switch on (IG).

    • Do not rotate the spiral with sensor cable sub-assembly with the battery connected and the engine switch on (IG).


    1. Check that the engine switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. Check that the front wheels are facing straight ahead.

    4. Attach the 3 claws to install the spiral with sensor cable sub-assembly.

      Note

      When replacing the spiral with sensor cable sub-assembly with a new one, remove the lock pin before installing the steering wheel assembly.

    5. Connect each connector.

      Note

      When connecting any airbag connector, take care not to damage the airbag wire harness.

    6. B008IQ9C01
      *1 Slider
      *a Lock Position

      Connect the airbag connector and check that the slider is in the lock position.

      Tech Tips

      If the slider is not in the lock position, the airbag connector is not completely connected. Disconnect the airbag connector, check the airbag connector and spiral with sensor cable sub-assembly terminals and connector housings for deformation or foreign matter, and then reconnect the airbag connector.

  2. INSTALL UPPER STEERING COLUMN COVER

    for Manual Tilt and Manual Telescopic Steering Column:

    Click here

    for Power Tilt and Power Telescopic Steering Column:

    Click here

  3. INSTALL LOWER STEERING COLUMN COVER

    for Manual Tilt and Manual Telescopic Steering Column:

    Click here

    for Power Tilt and Power Telescopic Steering Column:

    Click here

  4. PLACE FRONT WHEELS FACING STRAIGHT AHEAD

  5. ADJUST SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY

    Note

    Do not adjust the spiral with sensor cable sub-assembly with the battery connected and the engine switch on (IG).


    1. Check that the engine switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. A01XOGFC01
      *A w/o Steering Heater
      *B w/ Steering Heater
      *1 Check Window
      *2 Colored Roller
      *3 U-turn Point

      Check the check window shown in the illustration.

      Tech Tips

      When the spiral with sensor cable sub-assembly is centered, the connector is at the top and the conditions below can be checked.


      • w/o Steering Heater:

        With the steering wheel straight ahead, the colored roller can be checked from the check window.

      • w/ Steering Heater:

        With the steering wheel straight ahead, the U-turn point of the cable can be checked from the check window.

    4. If the spiral with sensor cable sub-assembly is not centered, center it.


      1. A01XOTHC01
        *A w/o Steering Heater
        *B w/ Steering Heater
        *1 Interlock

        While pushing on the interlock indicated in the illustration, rotate the spiral with sensor cable sub-assembly counterclockwise slowly by hand until it stops.

        Note


        • When rotating the spiral with sensor cable sub-assembly, make sure to push on the interlock indicated in the illustration to release the interlock mechanism.

        • Do not turn the spiral with sensor cable sub-assembly using the airbag wire harness.

      2. A01XOASC01
        *A w/o Steering Heater
        *B w/ Steering Heater
        *1 Check Window
        *2 Colored Roller
        *3 U-turn Point

        Rotate the spiral with sensor cable sub-assembly 2.5 times clockwise from the lock position and check the check window.

        Tech Tips


        • The spiral with sensor cable sub-assembly will rotate approximately 2.5 turns to both the left and right from the center.

        • When the spiral with sensor cable sub-assembly is centered, the connector is at the top and the conditions below can be checked.


        • w/o Steering Heater:

          With the steering wheel straight ahead, the colored roller can be checked from the check window.

        • w/ Steering Heater:

          With the steering wheel straight ahead, the U-turn point of the cable can be checked from the check window.

        If the cable cannot be centered, it is possible that the spiral with sensor cable sub-assembly is broken. Replace the spiral with sensor cable sub-assembly with a new one.

  6. INSTALL STEERING WHEEL ASSEMBLY

    Click here

  7. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  8. PERFORM DIAGNOSTIC SYSTEM CHECK

    Click here

  9. CHECK SRS WARNING LIGHT

    Click here