POWER WINDOW REGULATOR MOTOR(for Front Door) INSPECTION

PROCEDURE

  1. INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

    Note:

    • Do not apply positive (+) battery voltage to any terminals, except terminal 2 (B), to avoid damaging the pulse sensor inside the motor.

    • Perform initialization of the power window system after removing, inspecting or replacing the power window regulator motor assembly LH.

    1. B405918C01

      *a

      Component without harness connected

      (Power Window Regulator Motor Assembly LH)

      *b

      Motor Gear
      V100135

      Clockwise
      V100136

      Counterclockwise

      w/ Jam Protection Function:

      1. Check that the motor gear rotates smoothly as follows.

        OK

        Measurement Condition

        Specified Condition

        1. Connect the positive (+) lead of the battery to terminal 2 (B) and the negative (-) lead to terminal 1 (GND), and hold for 3 sec. or more.

        2. While terminals 2 (B) and 1 (GND) are connected, connect the negative (-) lead of the battery to terminal 10 (UP).

        3. After disconnecting the negative (-) lead of the battery from terminal 10 (UP), connect terminal 10 (UP) to the negative (-) lead of the battery again within 1 sec.

        Motor gear rotates clockwise (UP)

        1. Connect the positive (+) lead of the battery to terminal 2 (B) and the negative (-) lead to terminal 1 (GND), and hold for 3 sec. or more.

        2. While terminals 2 (B) and 1 (GND) are connected, connect the negative (-) lead of the battery to terminal 7 (DOWN).

        3. After disconnecting the negative (-) lead of the battery from terminal 7 (DOWN), connect terminal 7 (DOWN) to the negative (-) lead of the battery again within 1 sec.

        Motor gear rotates counterclockwise (DOWN)

        If the result is not as specified, replace the power window regulator motor assembly LH.

    2. E270262C02

      *a

      Component without harness connected

      (Power Window Regulator Motor Assembly LH)

      *b

      Motor Gear
      V100135

      Clockwise
      V100136

      Counterclockwise

      w/o Jam Protection Function:

      1. Apply battery voltage to connector terminals 1 (D) and 2 (U).

        Note:

        Do not apply battery voltage to any terminals except terminals 1 (D) and 2 (U).

    3. Check that the motor gear rotates smoothly as follows.

      OK

      Measurement Condition

      Specified Condition

      Battery positive (+) → 2 (U)

      Battery negative (-) → 1 (D)

      Motor gear rotates clockwise

      Battery positive (+) → 1 (D)

      Battery negative (-) → 2 (U)

      Motor gear rotates counterclockwise

      If the result is not as specified, replace the power window regulator motor assembly LH.

  2. INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

    Note:

    • Do not apply positive (+) battery voltage to any terminals, except terminal 2 (B), to avoid damaging the pulse sensor inside the motor.

    • Perform initialization of the power window system after removing, inspecting or replacing the power window regulator motor assembly RH.

    1. B405917C01

      *a

      Component without harness connected

      (Power Window Regulator Motor Assembly RH)

      *b

      Motor Gear
      V100135

      Clockwise
      V100136

      Counterclockwise

      w/ Jam Protection Function:

      1. Check that the motor gear rotates smoothly as follows.

        Table 1. OK:

        Measurement Condition

        Specified Condition

        1. Connect the positive (+) lead of the battery to terminal 2 (B) and the negative (-) lead to terminal 1 (GND), and hold for 3 sec. or more.

        2. While terminals 2 (B) and 1 (GND) are connected, connect the negative (-) lead of the battery to terminal 10 (UP).

        3. After disconnecting the negative (-) lead of the battery from terminal 10 (UP), connect terminal 10 (UP) to the negative (-) lead of the battery again within 1 sec.

        Motor gear rotates counterclockwise (UP)

        1. Connect the positive (+) lead of the battery to terminal 2 (B) and the negative (-) lead to terminal 1 (GND), and hold for 3 sec. or more.

        2. While terminals 2 (B) and 1 (GND) are connected, connect the negative (-) lead of the battery to terminal 7 (DOWN).

        3. After disconnecting the negative (-) lead of the battery from terminal 7 (DOWN), connect terminal 7 (DOWN) to the negative (-) lead of the battery again within 1 sec.

        Motor gear rotates clockwise (DOWN)

        If the result is not as specified, replace the power window regulator motor assembly RH.

    2. E268557C05

      *a

      Component without harness connected

      (Power Window Regulator Motor Assembly RH)

      *b

      Motor Gear
      V100135

      Clockwise
      V100136

      Counterclockwise

      w/o Jam Protection Function:

      1. Apply battery voltage to connector terminals 1 (D) and 2 (U).

        Note:

        Do not apply battery voltage to any terminals except terminals 1 (D) and 2 (U).

      2. Check that the motor gear rotates smoothly as follows

        OK

        Measurement Condition

        Specified Condition

        Battery positive (+) → 1 (D)

        Battery negative (-) → 2 (U)

        Motor gear rotates clockwise

        Battery positive (+) → 2 (U)

        Battery negative (-) → 1 (D)

        Motor gear rotates counterclockwise

        If the result is not as specified, replace the power window regulator motor assembly RH.