PARKING BRAKE ASSEMBLY DISASSEMBLY

CAUTION / NOTICE / HINT

Note


  • When the brake pedal is first depressed after replacing the brake pads or pushing back the disc brake piston, DTC C1214 may be output. As there is no malfunction, clear the DTC.

  • While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or the door courtesy switch is turned on. Therefore, even if only brake pads are to be removed and installed, be sure to perform the Disable Brake Control procedure and disconnect the cable from the negative (-) terminal of the auxiliary battery before beginning work.

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. PRECAUTION

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal, Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notice before proceeding with work Click here.

  2. DISABLE BRAKE CONTROL

    Click here

  3. REMOVE REAR WHEEL

  4. SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY

    Click here

  5. REMOVE PARKING BRAKE SHOE ADJUSTING HOLE PLUG

  6. REMOVE REAR DISC

    Click here

  7. REMOVE PARKING BRAKE SHOE RETURN TENSION SPRING (for Front Side)


    1. B005ZBP

      Remove the parking brake shoe return tension spring.

  8. REMOVE PARKING BRAKE SHOE RETURN TENSION SPRING (for Rear Side)


    1. B005Z40

      Remove the parking brake shoe return tension spring.

  9. REMOVE BRAKE SHOE HOLD DOWN SPRING (for Front Side)


    1. B005Y2ME02

      Using SST, remove the brake shoe hold down spring as shown in the illustration.

      SST
      09718-00011

  10. REMOVE PARKING BRAKE SHOE STRUT


    1. B005ZLJ

      Pull the No. 1 parking brake shoe assembly towards the front of the vehicle by hand as shown in the illustration.

    2. B005Y0Z

      Remove the parking brake shoe strut.

  11. REMOVE BRAKE SHOE HOLD DOWN SPRING (for Rear Side)


    1. B005XVME02

      Using SST, remove the brake shoe hold down spring as shown in the illustration.

      SST
      09718-00011

  12. REMOVE PARKING BRAKE SHOE ADJUSTING SCREW SET


    1. B005XK3

      Expand the No. 1 and No. 2 parking brake shoe assemblies outward by hand and pull downward to separate them from the parking brake plate.

    2. B005ZQI

      Remove the parking brake shoe adjusting screw set.

  13. REMOVE NO. 1 PARKING BRAKE SHOE ASSEMBLY


    1. B005ZBL

      Remove the No. 1 parking brake shoe assembly.

  14. REMOVE PARKING BRAKE SHOE RETURN TENSION SPRING (for Lower Side)


    1. B005XKP

      Remove the parking brake shoe return tension spring.

  15. SEPARATE PARKING BRAKE SHOE LEVER


    1. B005XNO

      Using needle-nose pliers, separate the parking brake shoe lever from the No. 3 parking brake cable assembly as shown in the illustration.

  16. REMOVE PARKING BRAKE SHOE LEVER


    1. B005ZHJ

      Using a screwdriver, remove the parking brake shoe type C washer, parking brake shoe shim and the parking brake shoe lever.

      Tech Tips

      Parking brake shoe shims are provided when necessary to adjust the clearance between the parking brake shoe lever and parking brake shoe type C washer. Some vehicles may not be equipped with shims.

  17. REMOVE PARKING BRAKE SHOE HOLD DOWN SPRING PIN (for Front Side)


    1. B005Y2F

      Remove the parking brake shoe hold down spring pin.

  18. REMOVE PARKING BRAKE SHOE HOLD DOWN SPRING PIN (for Rear Side)


    1. Remove the rear axle hub and bearing assembly Click here.

    2. B005YBO

      Remove the nut to separate the parking plate sub-assembly from the rear axle beam assembly.

      Note

      Hang the parking plate sub-assembly using a wire or an equivalent tool.

    3. B005Y56

      Remove the parking brake shoe hold down spring pin.