FRONT SEAT ASSEMBLY(for Sedan) REMOVAL

CAUTION / NOTICE / HINT

CAUTION:

  • Be sure to read Precaution thoroughly before servicing.

    Click here

  • Wear protective gloves. Sharp areas on the seat frame and adjuster may injure your hands.

  • If the front seat airbag assembly was deployed, replace the front seat airbag assembly, front seatback frame sub-assembly, separate type front seatback cover and separate type front seatback pad with the necessary parts in accordance with the extent of the collision damage.

Tip:

  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE

  1. PRECAUTION

    Note:

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click hereClick hereClick here

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note:

    When disconnecting the cable from the negative (-) battery terminal, some systems need to be initialized after the cable is reconnected.

    Click hereClick hereClick hereClick hereClick here

  3. REMOVE FRONT SEAT HEADREST ASSEMBLY

    1. Remove the front seat headrest assembly from the front seat assembly.

  4. REMOVE FRONT OUTER SEAT TRACK BRACKET COVER (for Cold Area Specification Vehicles)

    1. Lift up the seat track adjusting handle and move the front seat assembly to the rearmost position.

    2. B334105

      Disengage the 2 claws to remove the front outer seat track bracket cover.

  5. REMOVE FRONT INNER SEAT TRACK BRACKET COVER (for Cold Area Specification Vehicles)

    1. B334106

      Disengage the 2 claws to remove the front inner seat track bracket cover.

  6. REMOVE SEAT TRACK COVER

    1. Lift up the seat track adjusting handle and move the front seat assembly to the foremost position.

    2. B347290

      Disengage the 2 claws to remove the seat track cover.

  7. REMOVE INNER SEAT TRACK BRACKET COVER

    1. B347289

      Disengage the claw and guide to remove the inner seat track bracket cover.

  8. REMOVE FRONT SEAT ASSEMBLY (w/o Front Seat Side Airbag)

    1. B347291

      Remove the 2 bolts on the rear side of the front seat assembly.

    2. Lift up the seat track adjusting handle and move the front seat assembly to the rearmost position.

    3. B347292

      Remove the 2 bolts on the front side of the front seat assembly.

    4. w/ Vertical Adjuster:

      1. Operate the vertical adjusting handle and move the front seat assembly to the uppermost position.

    5. Lift up the seat track adjusting handle and move the front seat assembly to the center position.

    6. Operate the reclining adjuster release handle and move the seatback to the upright position.

    7. Disconnect each connector and disengage each clamp under the front seat assembly.

    8. B347293

      Remove the front seat assembly.

      Note:

      Be careful not to damage the vehicle body.

  9. REMOVE FRONT SEAT ASSEMBLY (w/ Front Seat Side Airbag)

    1. B347291

      Remove the 2 bolts on the rear side of the front seat assembly.

    2. Lift up the seat track adjusting handle and move the front seat assembly to the rearmost position.

    3. B347292

      Remove the 2 bolts on the front side of the front seat assembly.

    4. w/ Vertical Adjuster:

      1. Operate the vertical adjusting handle and move the front seat assembly to the uppermost position.

    5. Lift up the seat track adjusting handle and move the front seat assembly to the center position.

    6. Operate the reclining adjuster release handle and move the seatback to the upright position.

    7. Disconnect the connector from the front seat airbag assembly under the front seat assembly.

      Note:

      When disconnecting any airbag connector, take care not to damage the airbag wire harness.

      1. B279750C10

        *a

        White Housing Lock

        *b

        Yellow CPA

        *c

        Slide

        Push down the white housing lock and slide the yellow CPA. (At this time, the connector cannot be disconnected yet.)

      2. Push down the white housing lock again and disconnect the connector.

        Note:

        Do not push down the part (A) shown in the illustration when disconnecting the connector.

    8. Disconnect each connector and disengage each clamp under the front seat assembly.

    9. B347293

      Remove the front seat assembly.

      Note:

      Be careful not to damage the vehicle body.