UPPER INSTRUMENT PANEL(for Sedan) REMOVAL

PROCEDURE

  1. PRECAUTION

    Click here

    Note:

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click hereClick here

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click hereClick here

  3. REMOVE NO. 2 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY

    1. B350630

      Using a moulding remover, disengage the claw and 2 clips and remove the No. 2 instrument panel garnish sub-assembly as shown in the illustration.

  4. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH

    1. Disconnect the front door opening trim weatherstrip LH.

  5. REMOVE INSTRUMENT SIDE PANEL LH

    1. B350632N01

      Using a moulding remover, disengage the 6 clips in the direction indicated by the arrow (1).

    2. Pull the instrument side panel LH in the direction indicated by the arrow (2) to disengage the 2 guides and remove the instrument side panel LH.

  6. REMOVE NO. 1 INSTRUMENT PANEL REGISTER SUB-ASSEMBLY

    B350634

    1. Disengage the 2 claws and 4 clips and remove the No. 1 instrument panel register sub-assembly.

  7. REMOVE NO. 1 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY

    1. Using a moulding remover, disengage the 12 claws, 10 clips and guide and remove the No. 1 instrument panel garnish sub-assembly as shown in the illustration.

      B350635

  8. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

    1. B350637

      Disengage the 8 claws and 5 clips.

    2. Disconnect each connector and remove the center instrument cluster finish panel sub-assembly.

  9. REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY

    1. B350664

      Disengage the 4 clips and 9 guides and remove the instrument cluster finish panel assembly as shown in the illustration.

  10. REMOVE COMBINATION METER ASSEMBLY

    Click here

  11. REMOVE FRONT PILLAR GARNISH LH

    w/o Curtain Shield Airbag:Click here

    w/ Curtain Shield Airbag:Click here

  12. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH

    1. Disconnect the front door opening trim weatherstrip RH.

  13. REMOVE INSTRUMENT SIDE PANEL RH

    1. B350642N01

      Using a moulding remover, disengage the 6 clips in the direction indicated by the arrow (1).

    2. Pull the instrument side panel RH in the direction indicated by the arrow (2) to disengage the 2 guides and remove the instrument side panel RH.

  14. REMOVE NO. 2 INSTRUMENT PANEL REGISTER SUB-ASSEMBLY

    1. Disengage the 11 clips and remove the No. 2 instrument panel register sub-assembly.

      B350641

  15. REMOVE FRONT PILLAR GARNISH RH

    Tip:

    Use the same procedure as for the LH side.

  16. DISCONNECT NO. 2 INSTRUMENT PANEL WIRE

    Click hereClick here

  17. REMOVE UPPER INSTRUMENT PANEL ASSEMBLY

    1. Disconnect each connector.

    2. Remove the bolt <A> and 2 clips.

      B352219

    3. Pull the upper instrument panel assembly in the direction indicated by the arrow (1) to disengage the 6 clips.

      B352220N01

    4. Pull the upper instrument panel assembly in the direction indicated by the arrow (2) to disengage the 5 guides and remove the upper instrument panel assembly.