КОРПУС КЛАПАНОВ В СБОРЕ УСТАНОВКА

Note

When working with FIPG material, perform the following:


  • Using a razor blade and gasket scraper, remove all old FIPG material from the gasket surfaces.

  • Clean all components thoroughly to remove all foreign matter.

  • Clean both sealing surfaces with a non-residue solvent.

  • Apply FIPG material in a continuous line approximately 1 mm (0.04 in.) in diameter on the sealing surface.

  • Reassemble parts within 10 minutes of applying FIPG material. Failing to do so will require the FIPG material to be removed and reapplied.


  1. INSTALL TRANSMISSION VALVE BODY ASSEMBLY

    A01DVLEE01

    1. Install the shift solenoid valve SL with the bolt.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

    2. Install the shift solenoid valve S1 and S2 with the bolt.

      Torque:
      6.6 N*m  { 67 kgf*cm, 56 ft.*lbf }

    3. Install the shift solenoid valve SLT with the plate and bolt.

      Torque:
      6.4 N*m  { 65 kgf*cm, 56 ft.*lbf }
    4. A01DZVUE01

      Align the groove of the manual valve with the pin of the lever.

    5. A01E2PQE02

      Install the 20 bolts.

      Torque:
      11 N*m  { 112 kgf*cm, 8 ft.*lbf }

      Tech Tips

      Bolt length:

      23 mm (0.91 in.) for A

      28 mm (1.10 in.) for B

      36 mm (1.42 in.) for C

  2. INSTALL TRANSMISSION WIRE

    A01E2CYE01

    1. Coat a new O-ring with ATF and install it to the transmission wire.

    2. Install the transmission wire to the case, and install the stopper plate with the bolt.

      Torque:
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }
    3. A01E23EE01

      Connect the 4 connectors to the 4 shift solenoid valves.

  3. INSTALL VALVE BODY OIL STRAINER ASSEMBLY

    A01E1QKE03

    1. Install 5 new gaskets.

    2. Install the oil strainer with the 4 bolts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

      Tech Tips

      Bolt length:

      14 mm (0.55 in.) for A

      20 mm (0.79 in.) for B

      23 mm (0.91 in.) for C

  4. INSTALL AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY

    A01DZ72E02

    Tech Tips

    Remove any packing material and be careful not to spill oil on the contacting surfaces of the transmission case and oil pan.


    1. Install the 3 magnets to the locations indicated in the illustration.

    2. A01E2GYE01

      Apply FIPG to the oil pan as shown in the illustration.

      FIPG
      Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent

    3. Install the oil pan with the 19 bolts.

      Torque:
      7.4 N*m  { 75 kgf*cm, 65 in.*lbf }

  5. INSTALL TRANSMISSION OIL FILLER TUBE SUB-ASSEMBLY

    A01DZROE01

    1. Coat a new O-ring with ATF, and install it to the oil filler tube.

    2. Install the oil filler tube with the 2 bolts.

      Torque:
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }

    3. Install the oil dipstick.

  6. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

  7. PERFORM INITIALIZATION


    1. Perform initialization Click here.

      Note

      Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.

  8. ADD AUTOMATIC TRANSMISSION FLUID


    1. Add automatic transmission fluid Click here.

      Fluid type
      Toyota Genuine ATF TYPE T-IV

  9. INSPECT AUTOMATIC TRANSMISSION FLUID


    1. Inspect the automatic transmission fluid Click here.